Hunter 99116 - User Manual

www.HunterFan.com
1.888.830.1326
Model 99116
Universal Ceiling
Fan Remote Control
Installation
OR OR OR
Remove the canopy. If uncertain
how to remove it, reference the fan’s
owner’s manual. With wiring exposed,
it may be helpful to note existing wire
connections or take a digital photo for
reference. Remove the wire connectors
that connect the wires from the outlet
box to the fan, leaving the grounding
wires connected.
Before installing the
Universal Remote Control
Receiver, use the pull chains
to set the fan speed to HIGH
and the light to ON. Be
sure power is OFF before
proceeding with installation.
Ceiling
Plate
Receive
r
Canopy
Receiver
Canopy
Ceiling
Bracket
Receiver
Fan Body
Cable Tie
For low prole fans, the receiver should
be secured to the ceiling bracket with a
cable tie.
Receiver
Canopy
M0041-01 • 01/15/14 • © Hunter Fan Company
Turn Power
OFF
Choose the hanging system that most closely resembles the one used by your fan and install the receiver as shown and wire as directed.
Note: Some fans may have considerable excess lead wire. For easier canopy installation, cut the excess wire, leaving a minimum of 8” remaining. Re-strip the fan lead wires 1/2”. Place remaining excess
wire into the ceiling electrical box. The bracket and fan must remain properly grounded.
You may have installation issues if the fan is installed on an angled ceiling. For assistance, call 1-888-830-1326.
If you are installing multiple remote-controlled fans
on the same circuit breaker,
you may need to perform a few extra steps to prevent
interference or faulty operation of your remote controls.
Go to www.HunterFan.com/FAQs and click “How do I properly
install multiple remote-controlled fans?” for more information.
Wiring
CONNECT WIRES FROM RECEIVER TO FAN - Using the orange wire connectors, connect the blue wire from the
receiver to the blue wire (or possibly black with white stripe wire) from the fan. Connect the yellow wire from the
receiver to the black wire from the fan.
If you’re uncertain about wire colors or connections, please contact a qualied electrician.
CONNECT WIRES FROM RECEIVER AND FAN TO WIRES FROM OUTLET BOX - Using the orange wire connectors,
connect the black wire (ungrounded) from the ceiling to the black wire from the receiver. Connect the white wire
(grounded) from the ceiling to both the white wire from the receiver and the white wire from the fan.
AFTER ALL WIRES ARE CONNECTED and secured with wire connectors, re-install the canopy.
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
To avoid possible electrical shock, before installing or servicing your fan, disconnect
the power by turning off the circuit breakers to the outlet box and associated wall
switch location. If you cannot lock the circuit breakers in the off position, securely
fasten a prominent warning device, such as a tag, to the service panel.
F
R
O
M
C
E
I
L
I
N
G
F
R
O
M
R
E
C
E
I
V
E
R
black
blue
yellow
blue
F
R
O
M
F
A
N
F
R
O
M
R
E
C
E
I
V
E
R
black
white white (grounded)
black (ungrounded)
white
F
R
O
M
F
A
N

Summary

Installation Guide

Prepare for Installation

Turn power OFF, set fan speed to HIGH, light to ON. Note existing wiring before removing canopy.

Install Receiver and Wire

Place receiver as shown, connect receiver wires to fan and outlet box wires using provided connectors.

Multiple Fan Installation Tips

Prevent Interference

Follow specific steps to prevent interference or faulty operation when installing multiple remote-controlled fans.

Maintenance and Operation

Battery Replacement

Remove screw to access battery compartment. Replace with CR2032 battery, positive side up.

Remote Pairing Procedure

Pair remote by pressing Fan Off and High buttons within 3 minutes of restoring power.

Fan and Light Controls

Control fan speed using dedicated buttons. Use Light button to turn lights on/off and adjust brightness.

Transmitter Wall Mount

Use the included wall plate with posts to mount the transmitter when not in use.

Special Features and Troubleshooting

Safe-Exit Program

Provides light for approximately 30 seconds after turning lights off to allow safe exit.

Troubleshooting Common Issues

Addresses fan not starting, erratic remote control, and light dimming issues, including CFL bulb compatibility.

Warranty and Compliance

Limited Warranty Information

Details the one-year limited warranty against defects in material and workmanship.

Regulatory Compliance

FCC and Industry Canada compliance statements for safe operation and interference prevention.

Hunter 99116 Specifications

General

Brand	Hunter
Model	99116
Category	Remote Control
Language	English