To Next PageTo Next Page
Need help?Do you have a question about the Hunter SIMPLEconnect and is the answer not in the manual?
General| Type | Ceiling Fan |
|---|---|
| Connectivity | Wi-Fi |
| Smart Home Compatibility | Amazon Alexa, Google Assistant, Apple HomeKit |
| Blade Span | 52 inches |
| Number of Blades | 5 |
| Warranty | Limited Lifetime Motor Warranty |
| Control | Remote Control, App Control |
Assess location for clearance, secure mounting, and select the correct downrod based on ceiling height.
Follow electrical safety guidelines, use qualified electricians, and heed all general warnings.
Essential tools for fan installation include a ladder, screwdrivers, pliers, and wire strippers.
Power drill and 9/64" drill bit are optional but helpful for mounting to support structures.
Do not mix hardware from different bags; use symbols to identify correct parts.
For flat ceilings, use standard mounting with a standard downrod.
For angled ceilings, use a longer downrod and potentially an angled mounting kit.
Use a three-step method to determine if your ceiling angle exceeds 34 degrees.
Turn power off, check bumpers, and orient the bracket correctly for angled ceilings.
Secure bracket using wood screws into structure or machine screws into fan-rated outlet box.
Choose between standard, shorter, or longer downrods based on ceiling height for proper fan installation.
Follow illustrated steps to remove the existing downrod pipe and reassemble with a new one.
Remove the pre-installed setscrew, insert the downrod, and securely tighten the setscrew with pliers.
Cut wires to length, leaving at least 8 inches extending from the top of the downrod, then strip ends.
Pass wires and downrod through the canopy, allowing it to rest loosely on the fan.
Place the downrod ball into the slot in the ceiling bracket, avoiding picking the fan up by the canopy or wires.
Place the receiver on top of the downrod assembly as shown in the diagram.
Connect the three grounding wires (ceiling, downrod, bracket) using an orange wire connector.
Push wire splices upward into the hanger bracket and outlet box, organizing grounded and ungrounded wires.
Connect the yellow wire from the receiver to the fan's black wire, and the blue wire to the fan's blue wire.
Connect ceiling black wire to receiver black wire, and ceiling white wire to receiver and fan white wires.
Position the canopy so it fits into the hanging bracket as shown in the illustration.
Lift the canopy, align screw holes, and insert the two canopy screws to secure it.
Align the three blade holes with the three blade iron posts for attachment.
Squeeze the blade and iron post together; flared tops should be visible when properly assembled.
Partially install switch housing screws and connect colored plugs between upper and lower housings.
Align notches, twist lower housing to lock, thread fan pull chain through the light kit hole.
Refer to website FAQs for instructions on installing the fan without a light kit.
Install the included LED bulbs into the sockets; replace with same wattage if necessary.
Press globe and keeper flush, thread pull chains, and screw the finial onto the threaded rod.
Connect pull chain pendants and note fan operation controls for speed and light.
Open battery compartment by removing the screw, install a CR2032 battery with the positive side up.
Pair remote by cycling power and pressing Fan OFF/ON buttons if the remote is not pre-paired.
Use the remote for fan/light ON/OFF and pull chains for fan speed and light control.
The Safe-Exit feature provides timed lighting upon turning off the room lights for safe exit.
Download the SIMPLEconnect app and ensure a compatible receiver is installed in your fan.
Insert the plug-in controller, record its PIN, and ensure Bluetooth is enabled on your device.
Launch the app and tap the correct controller button to initiate pairing.
Enter the controller's PIN, tap the gear icon, and select a room for the fan.
Tap the Pair button in Advanced Features, then cycle power to the fan within three minutes for pairing.
Confirmation of successful setup; tap back twice to control the fan via the app.
Unscrew the finial, remove globe keeper and globe, then unscrew and replace bulbs.
Move the reverse switch to the opposite position to change the direction of air flow.
Use soft brushes or cloths for cleaning to prevent scratching and damage to finishes.
Troubleshoot by checking power, pull chains, motor reversing switch, circuit breaker, and wiring connections.
Address wobbling by tightening screws, checking hanger ball seating, and using the balancing kit.
Resolve noise by tightening blade screws and checking for cracked blades.
Operate multiple fans by installing additional receivers and repeating the setup process for each fan.
