Why is my Husqvarna Viking Huskylock 910 Sewing Machine breaking threads?
Thread breakage can occur due to several reasons. The machine might be improperly threaded, so re-threading is recommended. Also, the thread tension(s) may be too tight, requiring a reset. Finally, the needle tension setting might be incorrect, suggesting a reset or a needle replacement.
Why is my Husqvarna Viking Huskylock 910 Sewing Machine skipping stitches?
Skipping stitches may occur if the needle is bent or blunt, suggesting you insert a new needle. The needle might also be inserted incorrectly, so try resetting it. Improper threading can also cause this issue, so re-thread the machine.
What to do if Husqvarna Viking Sewing Machine does not feed properly?
If the machine isn't feeding fabric correctly, the pressure on the presser foot might be insufficient; increase it by setting the lever to 5. Also, the differential feed might not be set correctly, so adjust it.
What to do if my Husqvarna Viking Sewing Machine needle breaks?
If the needle breaks, it might be due to a bent or blunt needle, in which case you should insert a new one. Another cause could be incorrect needle insertion, so try resetting it. Also, pulling the fabric while sewing can cause the needle to break, so avoid pulling the fabric.
What to do if my Husqvarna Viking Sewing Machine is puckering the fabric?
Puckering can happen if the needle thread tensions are too tight, so you should loosen them. Improper threading may also be the cause, thus re-threading the machine is advisable. Another potential reason is the need for differential feed; in this case, set the differential feed to 0.5-N.
General| Brand | Husqvarna Viking |
|---|---|
| Model | Huskylock 910 |
| Category | Sewing Machine |
| Language | English |
Identifies and labels the components of the Model 905 sewing machine.
Identifies and labels the components of the Model 910 sewing machine.
Instructions for preparing the sewing machine, focusing on the handwheel.
Step-by-step guide for changing the presser foot.
How to open and close the front cover, including safety switch information.
Details on accessing the accessory box and connecting the sewing machine power and foot control.
Adjusting sewing speed and using the telescopic thread stand.
Step-by-step guide for safely replacing the sewing machine needle.
Procedure for changing threads, using thread nets, and spool holders.
Instructions for operating the stitch finger lever and adjusting the presser foot lift.
Steps to disengage the upper cutter for edge sewing, with safety notes.
Guidance on removing and using the free arm for sewing small areas.
Detailed instructions for threading the upper looper.
Detailed instructions for threading the lower looper.
Step-by-step guide for threading the needles.
Final checks before sewing, including thread path and cutter operation.
How to adjust presser foot pressure for different fabric types.
A recommended table for setting thread tensions for various stitches.
Guidance on adjusting thread tension dials for correct stitch formation.
Illustrations and solutions for common thread tension problems.
How to adjust stitch width, cutting width, and stitch length.
Guide to using differential feed for various fabrics and gathering.
Explanation of the LCD display, buttons, and their functions on Model 910.
Procedure for choosing the preferred language for the display.
How to use Auto Mode for recommended stitch settings.
Guide to selecting programmed stitches and fabric types in Auto Mode.
Introduction to Manual Mode for custom adjustments and settings.
How to store and retrieve custom stitch settings using memory.
Procedures for memory management and reference to stitch/fabric tables.
Instructions for performing a four-thread overlock stitch with two needles.
How to chain off stitches and cut the thread chain.
Methods for using cording or decorative threads to strengthen seams.
Techniques for guiding fabric when sewing inside and outside curves.
How to set up and sew three-thread overlock stitches by removing a needle.
Instructions for performing a two-thread overlock stitch using the 2-thread converter.
Instructions for performing a two-thread overlock stitch on Model 910.
Methods for sewing a flatlock stitch, including with a multipurpose foot.
A table detailing stitch settings for two-thread sewing operations.
How to perform three-thread and two-thread rolled edge stitches.
Instructions for creating pin tucks using the multipurpose foot.
Safety precautions and procedures for replacing the sewing machine light bulb.
Procedures for cleaning the machine after use and for proper storage.
Step-by-step guide for replacing the lower cutter.
Guidance on lubricating moving parts for smooth operation.
To Next Page