What does it mean if the green activate LED is flashing on my Husqvarna 535i XP Chainsaw?
If the green activate LED is flashing on your Husqvarna Chainsaw, it means that the battery voltage is low. To fix this, charge the battery.
Why is the warning indicator flashing on my Husqvarna Chainsaw?
The warning indicator flashes because of a temperature deviation. To resolve this, ensure the battery is used in surroundings where temperatures are between 5°C/41°F and 40°C/104°F.
What to do if the red error LED comes on on my Husqvarna 535i XP Chainsaw?
The red error LED indicates that the cell difference is too much (1V). Speak to your servicing dealer.
Why Husqvarna 535i XP won't start and no LEDs are on?
If your Husqvarna Chainsaw doesn't start and no LEDs light up when you press the power button, there could be several reasons. First, the battery might be defective; press the on/off button to check the battery – at least one green LED should illuminate. Other potential causes include a defective connection between the battery and the product (ensure the connectors are clean and undamaged), a faulty connection in the keypad connector (make sure it's correctly assembled, dry, undamaged, and free from corrosion), a broken keypad (replace it), damaged cables between the control unit and keypad/main switch (repair or replace them if damaged), or a short circuit in the control unit (replace it).
What to do if a warning sign flashes red on the battery of Husqvarna Chainsaw?
If a warning sign flashes red on the Husqvarna Chainsaw battery when you press the start button, it could be due to several reasons: the battery temperature might be too high (wait until it cools down, or insert it into the charger to cool it faster), the voltage might be too low (charge the battery), the temperature could be too low (ensure the battery temperature is above -10° C), or the battery itself might be defective (replace it).
Why is the red error LED flashing on my Husqvarna Chainsaw?
The red error LED on your Husqvarna Chainsaw flashes because: * The battery is empty, so you should charge the battery. * There is a temperature deviation. Use the battery in temperatures between -10°C (14°F) and 40°C (104°F). * There is an overvoltage. Remove the battery from the battery charger.
What to do if a red warning sign flashes on the charger of Husqvarna Chainsaw?
If a red warning sign flashes on the charger of your Husqvarna Chainsaw when the battery is attached, it could be due to several reasons: a defective connection between the charger and battery (ensure the power plugs are clean and undamaged), the battery temperature being too high (let the battery cool in the charger for 1-5 minutes), the ambient temperature being too low (ensure it's above 5°C), the battery temperature being too low (ensure it's above 5°C), a defective battery (check by pressing the battery start button; at least one green LED should light up, if not, replace the battery), or a defective charger (disconnect the charger from the mains for 1 minute, then reconnect; the fan should start and a green LED should light up for 3 seconds, if not, replace the charger).
What to do if the warning indicator is flashing on my Husqvarna 535i XP Chainsaw?
The warning indicator might flash on your Husqvarna Chainsaw due to several reasons: * The chain brake may be engaged. To solve this, pull back the front hand guard to release the chain brake. * There could be a temperature deviation. In this case, allow the product to cool down. * The cutting attachment might be jammed due to overload. If so, release the cutting attachment. * The power trigger and the activate button may have been pressed simultaneously. Release the power trigger to activate the product.
What does it mean if a warning sign on the keypad flashes after start on Husqvarna 535i XP Chainsaw?
If a warning sign on the keypad of your Husqvarna Chainsaw flashes after you start it and then the product stops, it could be due to several reasons: the power trigger might have been pushed during start (avoid pushing the power trigger when starting the product), there might be water in the main switch signal connector (disassemble and dry the stop signal connector, then reassemble it), there could be a short circuit in the keypad (replace the keypad), or there might be a short circuit in the main switch (replace the main switch).
What does it mean if a warning sign shows a red light on Husqvarna 535i XP keypad?
If a warning sign shows a red light on the keypad of your Husqvarna Chainsaw, it indicates that permanent error codes are preventing the product from running. Erase the error codes using a diagnostic tool. Alternatively, the control unit might be broken and need replacement.
General| Battery Voltage | 36 V |
|---|---|
| Weight (excluding battery and cutting equipment) | 2.6 kg |
| Chain Speed at Max Power | 20 m/s |
| Sound Pressure Level at Operator's Ear | 94 dB(A) |
| Recommended Bar Length | 12-16 inches |
| Oil Tank Volume | 0.2 liters |
| Chain Pitch | 3/8 inch |
| Chain Gauge | 0.043 in |
To Next Page
