How to fix a break in the boundary loop of my Husqvarna AUTOMOWER 315X?
To fix a break in the boundary loop, find where the break is located. Replace the damaged section of the loop with a new loop wire, and splice it using an original coupler.
Why is my Husqvarna Lawn Mower charging station showing a red flashing light?
A red flashing light on your Husqvarna Lawn Mower charging station indicates an interruption in the charging station’s antenna. Unfortunately, I cannot provide specific troubleshooting steps for this issue. Please contact your local Husqvarna representative for assistance.
How to fix 'No loop signal' on a Husqvarna AUTOMOWER 315X?
The 'No loop signal' message on your Husqvarna Lawn Mower can appear if the boundary wire is crossed on its way to and from an island. Check that the boundary wire is laid according to instructions, ensuring it's in the correct direction around any islands. Also, disturbances from metal objects (fences, reinforcement steel) or buried cables nearby can cause this issue. Try moving the boundary wire or creating islands in the work area to boost the signal strength. Another possibility is that the mower is too far from the boundary wire. Redo the boundary wire installation to ensure all parts of the work area are a maximum of 35 m / 115 ft from the boundary wire.
What to do if the cutting system of my Husqvarna AUTOMOWER 315X Lawn Mower is blocked?
If the cutting system of your Husqvarna Lawn Mower is blocked, there are a few possible reasons. It could be that grass or another object has become wrapped around the blade disc; in this case, check the blade disc and remove any obstructions. Another possibility is that the blade disc is sitting in a pool of water; if so, move the product and try to prevent water from collecting in the work area. Finally, the grass may be too high. Cut the grass before installing the product, ensuring it's no more than 10 cm / 3.9 in.
How to fix a blocked wheel motor on my Husqvarna AUTOMOWER 315X?
If the wheel motor of your Husqvarna Lawn Mower is blocked, it's likely due to grass or another object wrapped around the drive wheel. To resolve this, check the drive wheel and carefully remove any obstructions.
What to do if the Husqvarna AUTOMOWER 315X Lawn Mower has a blue flashing light?
If your Husqvarna Lawn Mower is showing a blue flashing light, it could be due to a couple of reasons. First, the boundary loop might not be properly connected to the charging station. Make sure the boundary wire connectors are correctly fitted. Alternatively, there might be a break in the boundary loop. If so, locate the break, replace the damaged section with a new loop wire, and splice it using an original coupler.
How to find breaks in the loop wire of a Husqvarna Lawn Mower?
If the loop wire of your Husqvarna Lawn Mower is broken, it's often due to unintentional physical damage, like accidentally cutting it while gardening, or stretching the wire too much during installation. To find the break, try halving the loop's distance where you suspect the damage. Keep halving the distance until you're left with a very short section of wire. This should help you pinpoint the location of the break.
Why is the light flashing blue on my Husqvarna AUTOMOWER 315X?
A blue flashing light indicates that the boundary loop is not connected to the charging station. Ensure that the boundary wire connectors are properly fitted to the charging station.
Why does my Husqvarna AUTOMOWER 315X say 'No loop signal'?
This can occur when ECO mode is active and the mower tries to start outside the charging station. Place the Husqvarna Lawn Mower in the charging station, initiate the start sequence, and then close the hatch. It may also happen if the pairing between the mower and the charging station is lost. In this case, place the mower in the charging station and generate a new loop signal.
Why is the Husqvarna AUTOMOWER 315X Lawn Mower showing a blue flashing light?
If the Husqvarna Lawn Mower displays a blue flashing light, it typically indicates a problem with the boundary loop connection or a break in the loop. First, ensure the boundary wire connectors are correctly attached to the charging station. If the problem persists, there may be a break in the boundary loop. Locate the break, replace the damaged wire section with a new one, and securely splice it using an original coupler.
Provides essential safety guidelines for operating and maintaining the robotic lawnmower.
Specific safety precautions to follow during the robotic lawnmower's operation.
Guidelines and methods for laying the boundary wire around the work area.
Initial setup and automatic calibration process for the mower.
How to schedule mowing times and set operating periods.
Configuration of security levels, PIN codes, and alarms for the mower.
Step-by-step guide on how to start the robotic lawnmower.
Explanation of different operating modes like Main Area, Secondary Area, and Spot Cutting.
Procedure for safely replacing worn or damaged blades for optimal cutting.
Lists common fault messages, their causes, and suggested actions.
General| Product Name | Husqvarna AUTOMOWER 315X |
|---|---|
| Category | Lawn Mower |
| Cutting Width | 22 cm |
| Cutting Height Min | 20 mm |
| Cutting Height Max | 60 mm |
| Battery Type | Li-ion |
| Typical Charging Time | 60 min |
| Typical Mowing Time on One Charge | 70 min |
| Sound Level | 60 dB(A) |
| Working Area Capacity | 1600 m² |
| GPS-assisted Navigation | Yes |
| Automower Connect | Yes |
| Battery Voltage | 18 V |
| Cutting Height Adjustment | Electric |
| Connectivity | Bluetooth, Cellular |
| Weather Resistance | Yes |
| Blade Type | 3 pivoting blades |
To Next Page
