What to do if my Husqvarna Automower has no drive?
If your Husqvarna Lawn Mower has no drive, free the mower from any obstructions and address the reason it lacks drive. If the issue is due to wet grass, allow the lawn to dry before using the mower again.
How to fix uneven mowing results with my Husqvarna Lawn Mower?
If your Husqvarna Lawn Mower is giving uneven mowing results, there could be several reasons. It might not be mowing for enough hours each day, so try increasing the mowing time. The working area could also be too large; consider limiting it or extending the working time. Dull blades can also cause this, so replace them, along with the screws, to ensure balanced rotation. If the grass is too long for the set cutting height, increase the cutting height and then gradually lower it. If the mower seems to work more at the top of a slope, change the Garden shape setting to Open. Lastly, check for grass accumulation by the blade disc or around the motor shaft, and clean if necessary.
Why does my Husqvarna Automower Lawn Mower need manual charging?
If your Husqvarna Lawn Mower requires manual charging, it's because it is set in MAN operating mode. This is normal, so no action is needed.
Why is my Husqvarna Automower giving uneven mowing results?
Uneven mowing results with your Husqvarna Lawn Mower can stem from several factors. The mower might not be running enough hours daily, the working area could be too large, or the blades may be dull. Also, long grass relative to the cutting height, the mower working more at the top of a slope, or grass accumulation around the blade disc or motor shaft could contribute. Increase mowing time, limit the working area, replace blades, raise cutting height gradually, change the Installation shape setting to Open, and ensure the skid plate and blade disc rotate freely by cleaning any debris.
Why is my Husqvarna Lawn Mower running at the wrong time?
If your Husqvarna Lawn Mower is operating at incorrect times, the clock may need setting. Also, the start and stop times for mowing might be configured incorrectly; adjust these settings as needed.
What to do if my Husqvarna Automower Lawn Mower displays 'Wrong PIN code'?
If your Husqvarna Lawn Mower displays 'Wrong PIN code', enter the correct PIN. After three incorrect attempts, the keypad will be blocked for five minutes.
What causes a left or right wheel drive system defect in Husqvarna Automower Lawn Mower?
A left or right wheel drive system defect in your Husqvarna Lawn Mower can stem from: * A defective wheel motor. Check the wheel motors' function via Tools - Test - Power and Motors – Wheel motors (shortcut 5-2-1-1) or with Autocheck. * A defective control box, which may need replacement. * A damaged or defective lower section cable harness. Inspect the cable harness and connector for repairable defects.
What causes a blade motor drive defect in a Husqvarna Automower?
A blade motor drive defect in your Husqvarna Lawn Mower can be caused by: * A defective blade motor. Verify the blade motor speed via Tools - Test - Power & Motors – Blade motor (shortcut 5-2-1-2). The speed should be around 2,500 rpm. * A defective control box, which may require replacement. * A damaged or defective lower section cable harness. Inspect the cable harness and connector for any repairable defects.
Why is my Husqvarna Automower charging station blocked?
A blocked charging station on your Husqvarna Lawn Mower can be due to: * An obstacle in the N-field. Remove any obstructions and consider moving the charging station. * A defective charging plate (N-coil). Check the N-signal via the Quick check function (press and hold '0' for 2 seconds). Replace the charging plate if the N-value is below 100. * Poor contact between charging strips. Ensure the contact strips on the charging station are not jammed. Round off the charging strips on the Automower if necessary using emery cloth and lubricate with copper paste.
What should I do if my Husqvarna Automower Lawn Mower shows 'Low battery voltage'?
If your Husqvarna Lawn Mower displays a 'Low battery voltage' message, it might be having trouble finding the charging station. If this is not the case, try changing the position of the charging station. If the battery is old (1-4 years), it may be spent and need replacement by a dealer.
General| Brand | Husqvarna |
|---|---|
| Model | Automower |
| Category | Lawn Mower |
| Language | English |
Warning to set the main switch to OFF when working on the mower's underframe.
Provides guidance on the ideal placement of the charging station.
Step-by-step guide to positioning and securing the charging station.
Explains the methods for installing the boundary wire (stapling or burying).
Details how to lay the boundary wire for optimal coverage and obstacle avoidance.
Specifies boundary wire placement relative to obstacles like walls or fences.
Solutions for narrow passages, including guide wires and corridor width.
Details on laying boundary wire across slopes, including limitations and exceptions.
Tips for stapling or burying the boundary wire for optimal placement.
Instructions on splicing the boundary wire using a solderless coupler.
Step-by-step guide to connecting the boundary wire to the charging station.
How to verify the boundary wire loop signal using the charging station LED.
Steps to link the Automower to the charging station and initial setup.
Explains the purpose and installation of guide wires.
Situations where a guide wire is recommended for efficient operation.
How to place and connect guide wires to the charging station.
How to route guide wires through passages for mower access.
Steps for connecting the guide wire to the boundary wire using a coupler.
Steps to start the Automower, including PIN code entry and safety checks.
Instructions on using the main ON/OFF switch for starting and safety.
Setting specific start and stop times for each day.
Adjusting how the mower leaves the charging station, including sectors and reversing distance.
Guiding the mower to remote areas using boundary or guide wires.
Controlling how the mower searches for the charging station using wires.
Defining distances from wires to create a 'corridor' for mower navigation.
Testing how the Automower finds its way into the charging station.
Testing different charge exit settings and distances to remote areas.
Advanced settings for checking loop signal and adjusting drive-past wire distance.
Settings for PIN code, time lock, stop protection, and settings lock.
How to change the mower's PIN code.
Function to prevent unauthorized use by requiring PIN after set days.
Activates an alarm if the PIN is entered incorrectly after stopping the mower.
Prevents unauthorized changes to settings or program selection.
Instructions for cleaning, charging, and storing the Automower and charging station.
How to clean the mower's underframe, blade disc, and check for free rotation.
Warning about using original parts and potential injury from incorrect replacement.
Step-by-step guide on how to replace the mower's blades.
Troubleshooting for motor blockages and blade disc issues.
To Next Page
