Husqvarna DM400 - User Manual

Questions and Answers

C
Casey MortonAug 17, 2025
What to do if my Husqvarna DM400 stops?
- W
  William BanksAug 17, 2025
  If your Husqvarna Drill stops, there could be several reasons. It could be a fault with the current source, in which case you should check the current source. The drill bit might be blocked; try turning it right and left with a wrench and carefully remove the drill from the hole. Also, too high a load can overload the motor; ensure the drill bit can turn easily in the hole. Finally, if there is a red light on the PRCD, push the RESET button. If it disconnects again, contact an approved Husqvarna service center.
V
Vincent JonesAug 20, 2025
Why does unwanted material collect around the hole during Husqvarna DM400 Drill operation?
- M
  middletonamandaAug 20, 2025
  If unwanted material collects around the hole during your Husqvarna Drill operation, the water pressure might be too low. Increase the water pressure.
C
Corey CummingsAug 22, 2025
Why is unwanted material collecting around the hole when using my Husqvarna DM400?
- P
  padilladavidAug 22, 2025
  Unwanted material may collect around the hole during operation of your Husqvarna Drill if the water pressure is too low. Increase the water pressure.
F
Francisco HarrisAug 25, 2025
What to do if my Husqvarna DM400 Drill does not operate smoothly?
- J
  Janice MathewsAug 26, 2025
  If your Husqvarna Drill does not operate smoothly, it may be due to too high a load causing overload of the motor. Use less force when you drill.
M
Matthew MurrayAug 28, 2025
What to do if my Husqvarna DM400 Drill decreases in speed and stops?
- N
  nguyenmichaelAug 28, 2025
  If your Husqvarna Drill decreases in speed and stops, the diamond segments may be blunt. Sharpen the diamond segments with a SiC grind stone.
M
mendezmicheleAug 30, 2025
Why are the diamond segments on the drill bit of my Husqvarna Drill pulled out?
- J
  Jacob LindseyAug 31, 2025
  If the diamond segments on the drill bit of your Husqvarna Drill are pulled out, there may be much vibration in the product during operation. Use correct load when you operate the product.
S
Stephen WoodsSep 2, 2025
Why does unwanted material collect around the hole when using my Husqvarna Drill?
- R
  Richard HodgeSep 2, 2025
  If unwanted material collects around the hole during operation of your Husqvarna Drill, the water pressure may be too low. Increase the water pressure. Refer to Technical data on page 17.
A
Anthony RaySep 5, 2025
Why are the diamond segments on my Husqvarna Drill bit pulled out of their bond?
- T
  Thomas DixonSep 5, 2025
  If the diamond segments on the drill bit of your Husqvarna Drill are pulled out of their bond, there may be much vibration in the product during operation. Use correct load when you operate the product.
J
Jason JonesSep 8, 2025
Why does my Husqvarna Drill not operate smoothly?
- M
  Misty BakerSep 8, 2025
  If your Husqvarna Drill does not operate smoothly, it may be due to too high a load causing an overload of the motor. Use less force when you drill.
C
Calvin BryantSep 12, 2025
What to do if my Husqvarna Drill doesn't continue into the surface?
- Z
  zrogersSep 12, 2025
  If your Husqvarna Drill decreases in speed, stops, and does not continue into the surface, the diamond segments may be blunt. Sharpen the diamond segments with a SiC grind stone.