Why is no fuel flowing in my Husqvarna K1270 II?
If no fuel flows in your Husqvarna Cutter, the carburetor might not be adjusted correctly, so adjust it. Alternatively, there could be a blockage in the carburetor, requiring you to clean it. Also check the fuel filter for blockages; clean or replace the fuel filter if needed. Finally, inspect the fuel hose for damage or blockages and adjust it.
What to do if fuel flows but compression is low in my Husqvarna K1270 II?
If fuel flows but compression is low in your Husqvarna Cutter, the spark plug might be loose, so tighten it. Alternatively, there could be wear or damage on the cylinder and piston, requiring replacement. Another possibility is a gas leak around the cylinder and crankcase, in which case you should replace the gasket.
Why is Husqvarna K1270 II Cutter temperature too high?
If the temperature of your Husqvarna Cutter is too high, the air intake or cylinder flanges may be blocked, so clean them. Examine the belt and adjust the tension if the drive belt tension is not sufficient. If the clutch is defective, always cut at full throttle, but also examine the clutch and speak to your service agent.
What to do if Husqvarna K1270 II Cutter blade does not rotate when throttling up?
If the cutting blade of your Husqvarna Cutter doesn't rotate when you throttle up, it could be due to a loose or defective belt. Tighten the belt or replace it. Also, ensure the cutting blade is correctly installed. If the clutch is defective, speak to your service agent.
Why are vibration levels too high on Husqvarna Cutter?
Excessive vibration in your Husqvarna Cutter can be caused by an incorrectly installed or damaged cutting blade. Ensure the cutting blade is correctly installed and not damaged. Replace it if defective. If a vibration damping unit is defective, speak to your service agent.
General| Power output | 5.8 kW |
|---|---|
| Idling speed | 2700 rpm |
| Max. power speed | 9000 rpm |
| Spark plug | NGK BPMR7A |
| Sound pressure level at operator's ear | 104 dB(A) |
| Max cutting depth | 145 mm |
| Engine | 2-stroke |
| Blade diameter | 400 mm |
| Weight | 13.7 kg |
Defines owner's duties regarding product safety and knowledge.
Overview of the power cutters and their specific applications.
States warnings about chemicals causing cancer or reproductive harm.
Visual identification of components for the K1270 II model.
Visual identification of components for the K1270 II Rail model.
Explains warning symbols and provides details on decals and plates.
Information on start instructions, cutting equipment, and type plate.
Explains safety symbols and provides essential operational safety guidelines.
Details safety measures for product operation and the surrounding work environment.
Addresses risks from vibrations, exhaust fumes, and dust inhalation.
Specifies required PPE for safe operation.
Emphasizes inspection of safety devices like throttle lockout and stop switch.
Focuses on safety aspects of blade guard, muffler, and fuel handling.
General safety rules to follow before performing maintenance.
Warnings and guidelines for assembling cutting blades, including applicable types.
Describes bonded abrasive blades, their examination, and vibration.
Details on diamond blades, sharpening, wet/dry use, and spindle/flange inspection.
Procedures for blade installation, rotation checks, and reversing the cutting head.
Explains kickback phenomena, reactive force, and avoidance strategies.
Covers pinching kickback, pipe cutting, preventing kickback, and basic working methods.
Guides for minimizing dust during operation.
Guidelines for selecting, mixing fuel and oil, and safe fueling.
Step-by-step guides for starting cold and warm engines.
Instructions on how to safely shut down the product.
Warnings for rail fixture use and steps to prepare the cutting guide.
Procedures for attaching and using the rail fixture for accurate rail cutting.
Overview of daily, weekly, and monthly maintenance tasks.
Procedures for cleaning external parts, air intake, and inspecting the spark plug.
Instructions for replacing the drive belt and removing/installing the starter housing.
Guides for recoil spring, carburetor, fuel system, and filter maintenance.
Lists common problems, their causes, and possible solutions.
Steps to inspect nozzles and filter for the water delivery system.
Guidelines for safely transporting, storing, and disposing of the product.
Specifications for K1270 II and K1270 II Rail models.
Declared values for noise and vibration based on laboratory testing.
Details emission warranty, coverage, claims, and service locations.
To Next Page
