How to establish a Bluetooth connection on a Husqvarna PG 690?
To establish a Bluetooth® Low Energy (BLE) connection to your Husqvarna Floor Machine, first, ensure the product is connected to a power source. Then, verify that the battery pack switch for the BLE module is in the ON position. If issues persist, consult an approved service agent for assistance with a drained battery or damaged antenna/connection.
How to troubleshoot a Husqvarna Floor Machine that does not start?
If your Husqvarna Floor Machine isn't starting, first, ensure the extension cable is properly connected and undamaged; replace it if necessary. Next, check the emergency stop button on the control panel and/or the remote control; turn it clockwise to disengage. Also, verify that the safety switch in the electrical enclosure is closed to complete the circuit.
Why is my Husqvarna PG 690 Floor Machine difficult to hold onto?
If your Husqvarna Floor Machine is hard to hold, it could be due to several reasons. You may need to increase the number of diamond tools installed to decrease the load on the product and the operator. Also, the surface or operation might be using too much of the product's capacity; try adjusting the speed of the motors and/or the forward speed of the product across the floor. Another possible reason is that only one phase comes into the product, so you should check the power supply.
How to fix an irregular scratch pattern from my Husqvarna PG 690?
An irregular scratch pattern from your Husqvarna Floor Machine can be caused by several factors. First, check that all diamond tools are correctly attached and have the same height. Ensure that all segments are the same diamond grit and bond. If the diamond segments are rough, space out the rough diamond segments equally and operate the product on an abrasive surface until all segments have the same height. Also, make sure that all head locks are in position and tightened. Verify that all resins are the same diamond grit and bond and that there is no contamination; to clean the resin tools, operate them for a short time on a lightly abrasive surface. Examine the grinding discs for broken sections or too much movement.
What to do if my Husqvarna PG 690 has sudden unwanted movements?
Sudden unwanted movements in your Husqvarna Floor Machine can stem from a few issues. Check the grinding discs for damaged parts and excessive movement. Also, ensure that all diamond tools are correctly attached and at the same height. Finally, verify that all head locks are in position and tightened.
What to do if the display on my Husqvarna PG 690 Floor Machine goes to the main menu during operation?
If the display on your Husqvarna Floor Machine goes to one of the main menus during operation, try changing the radio channel to avoid interference in radio communication between the remote control and the product.
What to do if my Husqvarna PG 690 Floor Machine makes an irregular scratch pattern?
If your Husqvarna Floor Machine is making an irregular scratch pattern, check that all diamond tools are correctly installed and at the same height. Make sure all segments are the same diamond grit and bond. If segments are rough, space them out equally and operate the machine on an abrasive surface until they are the same height. Also, ensure all head locks are in position and tightened. Verify that all resin tools are the same diamond grit and bond, free from contamination; clean them by operating briefly on a lightly abrasive surface. Finally, examine the grinding discs for broken sections or excessive movement.
Why does my Husqvarna PG 690 Floor Machine have sudden unwanted movements?
If your Husqvarna Floor Machine experiences sudden, unwanted movements, inspect the grinding discs for damage or excessive movement. Ensure all diamond tools are correctly attached and at the same height. Also, verify that all head locks are in position and tightened.
What to do if Husqvarna PG 690 Floor Machine makes an irregular scratch pattern?
If the Husqvarna Floor Machine is producing an irregular scratch pattern, it might be because the diamond tools are incorrectly attached or are at different heights; ensure they are correctly installed and at the same height. Also, check that all diamond segments are of the same grit and bond. If some diamond segments are rough, space them out equally and operate the machine on an abrasive surface until they wear down to the same height. Make sure all head locks are present and tightened. Verify that all resin tools are of the same grit and bond and free from contamination; clean them by operating on a lightly abrasive surface. Finally, inspect the grinding discs for wear or damage.
Why is my Husqvarna PG 690 Floor Machine not easy to hold?
If the Husqvarna Floor Machine is difficult to hold, it might be due to several reasons. You may need to increase the number of diamond tools to decrease the load on the product and operator. Check if the large grinding drive motor is properly connected; if issues persist, contact an approved service agent. A broken belt could also be the cause, in which case a service center should replace it. Inspect the power supply to ensure all phases are connected. Also, try adjusting the speed of the motors and/or the forward speed of the product across the floor.
Essential warnings and precautions for safe operation and handling.
Lists required PPE for safe use, including eye, hearing, and respiratory protection.
Guidelines for safe operating environments and electrical precautions.
Precautions for battery handling, grounding, and extension cables.
Instructions for connecting the dust extractor and main power supply.
How to set operating speed and rotation direction for optimal results.
Procedures for starting and stopping the grinder using control panel or remote.
Solutions for issues preventing start-up or affecting performance.
Explanation of error codes and messages displayed on the remote control.
General| Voltage | 400 V |
|---|---|
| Weight | 190 kg |
| Working Width | 690 mm |
| Speed | 0-1500 rpm |
| Motor Power | 16.4 kW |
| Grinding Width | 690 mm |
| Grinding Discs | 3 |
| Drive system | Planetary |
| Frequency | 50 Hz |
| Dust extraction | Yes |
| Water connection | Yes |
To Next Page