HydraMaster Titan 575 User Manual (English)

Other manuals for HydraMaster Titan 575

Owner’S Guide And Maintenance Schedule57 pages

Questions and Answers:

K
Kenneth SmithSep 5, 2025
What to do if my HydraMaster Vacuum Cleaner system will not prime?
- K
  Kenneth HallSep 6, 2025
  If the system won't prime, consider these possibilities: * Faulty check valves in the chemical pump: Remove and inspect the valves, cleaning or replacing them as needed. * A faulty chemical pump diaphragm: Remove and inspect, replacing if necessary. * A faulty check valve in the high-pressure pump: Remove and inspect the valve, cleaning or replacing as necessary. * A clogged filter on the feed line in the chemical jug: Inspect and clean it. * A loose, pinched, or damaged feed line from the chemical jug: Inspect and repair it. * A faulty chemical selector valve: Inspect the valve for leaks between ports and replace if necessary.
A
Alexander GreenSep 4, 2025
What to do if my HydraMaster Titan 575 has weak vacuum?
- R
  Richard StevensSep 4, 2025
  A weak vacuum could be caused by: * An air leak in the vacuum system: Check the vacuum relief valve for proper adjustment. * The vacuum blower turning too slowly: Check the engine rpm and adjust it to 3,000 rpm under a 12" Hg vacuum load. * A defective vacuum gauge: Test the gauge and replace it if necessary.
R
Rodney FowlerSep 3, 2025
Why is there chemical present in the water of my HydraMaster Titan 575 Vacuum Cleaner?
- M
  michaelsmithSep 4, 2025
  If you find chemical in the water, it could be due to a faulty chemical pump diaphragm or a faulty high-pressure check valve. Remove and inspect the chemical pump diaphragm and the valve, replacing as necessary.
E
Elizabeth HerreraSep 3, 2025
What to do if the vacuum blower on my HydraMaster Titan 575 is locked and will not turn?
- R
  robertstammySep 3, 2025
  If the vacuum blower on your HydraMaster Vacuum Cleaner is locked and won't turn, it could be due to rust buildup from inactivity. Try spraying penetrating oil into the blower and let it sit for at least an hour, then carefully use a pipe wrench on the outer diameter of the pulley on the coupler to free the blower lobes. If this doesn't work, there may be internal damage to the blower, and you should consult a qualified service technician.
S
Samantha SwansonSep 2, 2025
What to do if my HydraMaster Vacuum Cleaner psi gauge reads normal but there's low pressure from the wand?
- C
  coxrebeccaSep 2, 2025
  If your HydraMaster Vacuum Cleaner psi gauge reads normal but you're experiencing low pressure from the wand, there might be a restriction in the cleaning tool. Inspect the tool jet(s) and clean or replace as necessary. A faulty quick connect in the system could also be the issue, so inspect each one and replace as needed. Check for restrictions in the solution hoses by removing the quick connects and inspecting the hoses. Hard water deposits restricting the system can also cause this, so descale the truckmount.
W
Wayne SandersSep 1, 2025
Why won't the pump on my HydraMaster Titan 575 come up to normal cleaning pressure?
- K
  Kevin GloverSep 1, 2025
  If the pump on your HydraMaster Vacuum Cleaner isn't reaching normal cleaning pressure, the pressure adjusting valve might be faulty, so inspect, repair, or replace it. Worn seals or valves in the pump could also be the cause, so test the pump output volume. Additionally, check for a loose pump belt and adjust or replace it if necessary, as the pump rpm might be too low.
S
Shannon HayesAug 31, 2025
Why is there no pressure reading on my HydraMaster Titan 575 gauge?
- J
  Jessica NunezAug 31, 2025
  If there's no pressure reading on your HydraMaster Vacuum Cleaner gauge, the pump belt might be broken, so inspect and replace it if necessary. Alternatively, the gauge itself could be faulty, so try replacing it.
M
Matthew PatelAug 30, 2025
Why won't my HydraMaster Titan 575 engine come up to normal operating rpm?
- J
  Joyce CarterAug 30, 2025
  If the engine of your HydraMaster Vacuum Cleaner won't reach its normal operating RPM, it could be due to excessive load on the engine. Inspect and clean the recovery tank filters. It may also be caused by excessive back pressure on the engine exhaust, so inspect for blockage in the heat exchanger.
T
Tammy LewisAug 29, 2025
Why does my HydraMaster Titan 575 run rich (black smoke)?
- S
  sharonmurphyAug 29, 2025
  If your HydraMaster Vacuum Cleaner is running rich, producing black smoke, it could be due to a dirty air filter, so inspect and replace it if necessary. Another cause could be excessive back pressure, so inspect for a clogged heat exchanger, dirty air filter, or a partially opened choke.
J
Jesus WadeAug 28, 2025
Why does my HydraMaster Titan 575 Vacuum Cleaner run rough at high speed?
- D
  Danielle LunaAug 28, 2025
  If your HydraMaster Vacuum Cleaner runs rough at high speed, the spark plugs might be faulty, so remove and inspect them, cleaning or replacing as needed. Check the spark plug wires and connectors for damage or loose connections. Also, check for blockage in the fuel filter, as an inadequate fuel supply to the carburetor could be the issue. Verify there is a good contact with each of the wires to the coils.