6
Note: You can transmit an all call only when
the feature is enabled by your dealer. However,
you cannot call back an all call.
Calls on Analog Channels
To transmit a call on the analog channel, hold the PTT
key and speak into the microphone. To receive, release
the PTT key.
One Touch Call
You may request your dealer to set the One Touch Call
key for you. The One Touch Call feature is used to make
a call quickly. The call contact and call type are preset by
the dealer.
Operation: Press the programmed One Touch Call key
to initiate a call.
Time-out Timer (TOT)
TOT aims to prevent any user from occupying a channel
for an extended period. If the preset time expires, the
radio will automatically terminate the transmission and
keep beeping. To stop beeping, please release the PTT
key. You must wait for a certain time period (preset by
your dealer) to initiate another transmission.
Note: This feature is null in Emergency mode.
Busy Channel Lockout
If enabled (via the programming software), this feature
can prevent your radio interfering with other transmitting
radios on the same channel. If you hold the PTT key
while the channel is in use, your radio will keep beeping,
alerting you to transmission prohibition. When the
channel is free, you can hold the PTT key to transmit.
Pseudo Trunking
This feature can be enabled via the programming
software. If the radio operates on a channel with this
feature enabled and a time slot is already occupied, the
radio can transmit and receive in another free slot.
Functions and Operations
Rent
You can rent the radio from your dealer. When the rental
period expires, you are not allowed to use this radio.
If you rent this radio, please obtain the rental time
information from your dealer. If the Rent Pre-Alert feature
is enabled, the radio will give a tone periodically to
remind you the remaining time of your rental.
Scan
With the Scan feature, you can listen to communication
activities on other channels so that you can keep a close
track of your team members.
Operation:
1. To enable the feature, press the programmed Scan
key in standby mode (a high-pitched tone sounds); or
switch to a channel for which the Auto Scan feature is
enabled. When you switch to the channel, the radio
will start scan automatically.
2. After the feature is enabled, the radio will scan
according to the scan list set for the channel.
The scanning process is as follows:
● During scanning, the LED ashes orange.
● When activities are detected on a channel, the radio
will stay on the channel to receive current activities,
and the LED will glow green.
»
If you don’t want to hear the activities on the
channel, press the programmed Nuisance
Temporary Delete key to remove the channel
from the scan list temporarily.
»
If you want to continue listening to the activities
on the channel, press the programmed Monitor
key or Squelch Off key during scan stay.
»
To exit the scanning process, press the
programmed Scan key again (a low-pitched tone
sounds).
Roam ▼
This feature allows the radio to communicate between
sites in the same IP Multi-site Connect system. After
the feature enabled, the radio can communicate via any
site in the IP Multi-site Connect system, thus ensuring
seamless communication in the system.
Operation: You can enable or disable the Roam feature
by pressing the programmed Roam key.
Talk Around
You can continue to communicate in DM mode by
pressing the programmed Talk Around key when your
repeater malfunctions, or when your radio and the com-
municating radio are out of the repeater’s range but
within talking range of each other.
Operation: Press the programmed Talk Around key to
enable the feature (a high-pitched tone sounds). To dis-
able the feature, press this key again (a low-pitched tone
sounds).
Monitor
To adjust match conditions for signal receiving, you can
enable the Monitor feature.
Operation:
● Press the programmed Monitor key to enable the
feature (a high-pitched tone sounds). To disable the
feature, press this key again (a low-pitched tone
sounds).
● Hold down the programmed Monitor Momentary key
to enable the feature (a high-pitched tone sounds).
To disable the feature, release this key (a low-pitched
tone sounds).
Squelch Off
If the Squelch Off feature is activated, the speaker will
keep unmuted no matter whether the signals are present.
Operation:
● Press the programmed Squelch Off key to enable
the feature (a high-pitched tone sounds). Then the
To Next Page
Loading...
Need help?
General
