Why does my IAME Engine start then stop?
If your IAME Engine starts but stops after a few seconds when turning the key to the RUN position, begin by checking the stator connector for bad cable connections. If that's not the issue, it could be an electronic box or starter failure, in which case you should contact Authorized Service Centers. Also, check the carburetor adjustment.
What to do if IAME Parilla Leopard RL cranks but doesn't start?
If the starter of your IAME Engine cranks, but the engine doesn’t start when turning the key in the RUN position, there are several things to inspect. First, check the cable connections. Then, inspect the H.T. coil connection for any issues or failures and replace if needed. Ensure the H.T. coil is properly grounded. If the problem persists, it could be an electronic box or ignition failure, requiring assistance from Authorized Service Centers. Also, check for a wet spark plug and replace it if necessary. Inspect the induction system for any malfunctions, checking the status and connection of the fuel pipe. You may also need to replace the gaskets and membranes on the carburetor. Finally, inspect the reed petals and replace them if necessary.
Why is there a drop in IAME Parilla Leopard RL Engine performance?
If you notice a drop in performance in your IAME Engine, several factors could be responsible. Start by checking the piston for bad compression. Also, check the carburetor adjustment. Ensure there is sufficient gas flow by inspecting the fuel flow lines and inlet filter. Finally, check the inlet silencer and clean it if it's dirty.
Why does IAME Engine starter cranks after engine is running?
If the starter cranks even after the IAME Engine is running, it indicates an electronic box failure. In this case, you should contact Authorized Service Centers.
How to fix rough idle on IAME Parilla Leopard RL?
If your IAME Engine has a rough idle, it could be due to a bad carburetor adjustment. Check the carburetor adjustment.
What to do if IAME Parilla Leopard RL Engine has burning smell?
If you experience a burning smell or smoke coming from your IAME Engine, it could be due to overheating of the clutch. You should check the clutch.
Why does IAME Engine clutch engages at too high RPM?
If the clutch of your IAME Engine engages at too high RPM, it's likely due to excessive wear of the friction material. You should check the clutch.
Why is IAME Engine exhaust too noisy?
If the exhaust of your IAME Engine is too noisy, there are several potential causes. The flexible part may be damaged, so check it and replace it if necessary. The springs might be damaged or lost. The insulating strap could be damaged or lost. The exhaust header might also be damaged.
What to do if the IAME Parilla Leopard RL Engine starter won't crank?
If the starter of your IAME Engine doesn't crank when you turn the key to the RUN position, there are several potential causes. It could be due to bad connections on the starter cables, which you should check and tighten. Alternatively, there might be bad grounding; inspect the connections and tighten them as needed. Another possibility is an interruption on the fuse, requiring you to replace the 5A strip fuse, but first check for any battery polarity reversal. Damaged cables could also be the culprit, in which case they should be replaced. Also, check for loose battery connections and tighten them if necessary. If the battery is discharged, recharge it. A starter failure would necessitate an overhaul of the starter. A relay failure requires you to replace the relay. For issues related to ...
General| Displacement | 125cc |
|---|---|
| Fuel System | Carburetor |
| Ignition | Digital |
| Bore | 54.00 mm |
| Type | Two-stroke, single-cylinder |
| Cooling System | Liquid-cooled |
| Stroke | 54.50 mm |
| Carburetor | Tillotson HL334AB |
| Lubrication | Oil mixture |
Step-by-step guide to install the water pump, belts, and pulleys for the cooling system.
Steps for preparing and installing the motor mount, including drilling holes.
Instructions for mounting the carburetor, including gas cable clamp.
To Next Page