Why Rapid Resume Features screen does not appear in the Configuration/Setup Utility on IBM Desktop?
If the Rapid Resume Features screen does not appear in the Configuration/Setup Utility and the Rapid Resume Manager icon does not appear in the “AptivaWare” window of your IBM Desktop, this is normal if you upgraded the processor on your system board to a non-SL-Enhanced processor. Non-SL-Enhanced processors do not support Rapid Resume.
What to do if my IBM Aptiva Desktop turns off without warning?
If your IBM Desktop turns off unexpectedly, here's what to do: 1. If Standby is enabled, move the mouse. 2. If Rapid Resume and Automatic Power Off are enabled, or the Scheduler feature is set to turn off the system, turn the system back on. 3. Ensure both the system unit and monitor power cords are securely plugged into electrical outlets. 4. Verify all cables are correctly and securely connected to the system unit. 5. Check for blown fuses, tripped circuit breakers, or power failures. 6. Unplug the system unit power cord, wait 10 seconds, and plug it back in. If it doesn't start, press the on/off button.
Why can't I enter password on my IBM Desktop?
If you are unable to enter your password on your IBM Desktop, ensure you are typing the correct password. Also, verify that the keyboard cable is securely connected to the correct keyboard port (not the mouse port) on the back of the system unit.
What to do if IBM Desktop has error code, more than one beep, or continuous beep?
If your IBM Desktop displays an error code, consult “Error codes, descriptions, and corrective actions” on page 52 and follow the listed action. If no error code is displayed, refer to your Services and Support Guide for service information.
What to do if screen is black (no error code), more than one beep in self-test on IBM Desktop?
If you installed memory modules or adapter cards make sure you installed them correctly. For instructions on installing memory modules on your system board, see “Installing and removing memory modules” on page 111. For instructions on installing adapter cards in your system unit, see “Installing adapter cards” on page 86.
What to do if my IBM Desktop computer turns off without warning?
Here's what to do if your IBM Desktop computer turns off without warning: 1. If the Standby feature is enabled, move the mouse to exit Standby. 2. If the Rapid Resume feature is enabled and the Automatic Power Off option is set, or the Scheduler feature is set to turn the system unit off, turn the system unit back on. 3. Ensure that the system unit and monitor power cords are securely plugged into electrical outlets. 4. Verify that the cables are correctly and securely connected to the system unit. 5. Check for a blown fuse, tripped circuit breaker, or power failure. 6. Unplug the system unit power cord from the electrical outlet, wait 10 seconds, and then plug the power cord back into the electrical outlet. If the computer does not start immediately, push the on/off button on the s...
Why when I turn on the IBM Desktop, the desktop is not as I left it?
If, when you turn on your IBM Desktop, the desktop is not as you left it: 1. Ensure no one else has used the computer and changed the desktop. 2. Check that Rapid Resume is enabled. 3. Choose Rapid Resume from the Configuration/Setup Utility main menu, and ensure the APM BIOS Mode option is set correctly for your operating system: * OS/2 Warp: “16” or “32 Bit Protected”. * Windows: “32 Bit Protected”. * OS/2 2.1: “16 Bit Protected”. 4. If you are working in Windows, check that “POWER.EXE” is in the CONFIG.SYS file (make sure “REM” does not appear in front of “POWER.EXE”).
What to do if I pressed the on/off button on the IBM Desktop, but the computer has not turned off after 5 minutes?
If you pressed the on/off button on the system unit of your IBM Desktop, but the computer has not turned off after 5 minutes, check your Services and Support Guide for information on obtaining service.
Why does my IBM Desktop computer automatically turns off instead of entering Standby?
If your IBM Desktop computer turns off automatically instead of entering Standby, make sure the Standby timer is set to a shorter duration than the Automatic Power Off timer.
What to do if I can’t enter password on my IBM Desktop?
If you can’t enter your password on your IBM Desktop, follow these steps: 1. Double-check that you are typing the correct password. 2. Ensure the keyboard cable is correctly and securely connected to the keyboard port (not the mouse port) on the back of the system unit. The keyboard port has a symbol next to it. 3. If you have forgotten your password, check your Services and Support Guide for information on obtaining service.
Identifies essential computer components and peripherals to unpack from the system box.
Instructions for attaching computer components, noting color-coded connectors and safety advice.
Guidance on connecting power cords to the computer and monitor, and setting the voltage selector switch.
Initial step to power on the computer and connected monitor for setup.
Instructions for completing the Windows 98 operating system setup process.
Guide to installing additional programs from the Software Selections CD-ROM.
Instructions for connecting optional components like microphones, modems, and network cards.
General| CPU | Intel Pentium |
|---|---|
| RAM | 8 MB to 64 MB |
| Operating System | Windows 95 |
| Graphics | S3, ATI |
| Optical Drive | CD-ROM |
| Ports | Serial, Parallel, PS/2 |
| Expansion Slots | ISA, PCI |
To Next Page