Icom IC-7610

Cmd. Sub cmd. Data Description
0229 00 ~ 03 CW-KEY SET > Rise Time
(00=2 msec., 01=4 msec., 02=6 msec.,
03=8 msec.)
0230 00 or 01 CW-KEY SET > Paddle Polarity
(00=Normal, 01=Reverse)
0231 00 ~ 02 CW-KEY SET > Key Type
(00=Straight, 01=Bug, 02=Paddle)
0232 00 or 01 CW-KEY SET > MIC Up/Down Keyer
(00=OFF, 01=ON)
0233 00 ~ 03 RTTY DECODE SET > FFT Scope Averaging
(00=OFF, 01=2, 02=3, 03=4)
0234 see p. 12 RTTY DECODE SET >
FFT Scope Waveform Color
0235 00 or 01 RTTY DECODE SET > Decode USOS
(00=OFF, 01=ON)
0236 00 or 01
RTTY DECODE SET > Decode New Line Code
(00=CR, LF, CR+LF, 01=CR+LF)
0237 00 ~ 02 RTTY DECODE SET > Diddle
(00=OFF, 01=BLANK, 02=LTRS)
0238 00 or 01 RTTY DECODE SET > TX USOS
(00=OFF, 01=ON)
0239 00 or 01 RTTY DECODE SET > Auto CR+LF by TX
(00=OFF, 01=ON)
0240 00 or 01 RTTY DECODE SET > Time Stamp
(00=OFF, 01=ON)
0241 00 or 01 RTTY DECODE SET > Time Stamp (Time)
(00=Local, 01=“CLOCK2 UTC Offset” setting)
0242 00 or 01
RTTY DECODE SET > Time Stamp (Frequency)
(00=OFF, 01=ON)
0243 see p. 12 RTTY DECODE SET > Font Color (Receive)
0244 see p. 12 RTTY DECODE SET > Font Color (Transmit)
0245 see p. 12 RTTY DECODE SET > Font Color (Time
Stamp)
0246 see p. 12 RTTY DECODE SET > Font Color (TX Buffer)
0247 00 or 01 RTTY DECODE LOG > Decode Log
(00=OFF, 01=ON)
0248 00 or 01 RTTY DECODE LOG > Log Set > File Type
(00=Text, 01=HTML)
0249 00 ~ 03 PSK DECODE SET > FFT Scope Averaging
(00=OFF, 01=2, 02=3, 03=4)
0250 see p. 12 PSK DECODE SET > FFT Scope Waveform
Color
0251 00 or 01 PSK DECODE SET > AFC Range
(00=±8 Hz, 01=±15 Hz)
0252 00 or 01 PSK DECODE SET > Time Stamp
(00=OFF, 01=ON)
0253 00 or 01 PSK DECODE SET > Time Stamp (Time)
(00=Local, 01=“CLOCK2 UTC Offset” setting)
0254 00 or 01
PSK DECODE SET > Time Stamp (Frequency)
(00=OFF, 01=ON)
0255 see p. 12 PSK DECODE SET > Font Color (Receive)
0256 see p. 12 PSK DECODE SET > Font Color (Transmit)
0257 see p. 12
PSK DECODE SET > Font Color (Time Stamp)
0258 see p. 12 PSK DECODE SET > Font Color (TX Buffer)
0259 00 or 01 PSK DECODE LOG > Decode Log
(00=OFF, 01=ON)
0260 00 or 01 PSK DECODE LOG > Log Set > File Type
(00=Text, 01=HTML)
0261 00 or 01 SCAN SET > SCAN Speed
(00=SLow, 01=Fast)
0262 00 or 01 SCAN SET > SCAN Resume
(00=OFF, 01=ON)
0263 0000 ~ 0255 VOICE TX > TX LEVEL
(0000=0%, 0255=100%)
0264 00 or 01 VOICE TX SET > Auto Monitor
(00=OFF, 01=ON)
0265 01 ~ 15 VOICE TX SET > Repeat Time
(01=1 sec. to 15=15 sec.)
0266 00 or 01 Recorder Set > REC Mode
(00=TX&RX, 01=RX Only)
0267 00 or 01 Recorder Set > TX REC Audio
(00=Direct, 01=Monitor)
0268 00 or 01 Recorder Set > RX REC Condition
(00=Always, 01=Squelch Auto)
0269 00 or 01 Recorder Set > File Split
(00=OFF, 01=ON)
D Command table (Continued)
Cmd. Sub cmd. Data Description
0270 00 or 01 Recorder Set > PTT Auto REC
(00=OFF, 01=ON)
0271 00 ~ 03 Recorder Set > PRE-REC for PTT Auto REC
(00=OFF, 01=5 sec., 02=10 sec., 03=15 sec.)
0272 00 ~ 03 Player Set > Skip Time
(00=3 sec., 01=5 sec., 02=10 sec., 03=30 sec.)
0273 05 ~ 30 Instant Replay Set > REC Time
(05=5 sec., to 30=30 sec.)
0274 03 ~ 10 Instant Replay Set > Play Time
(03=3 sec., to 10=10 sec.)
0275 00 or 01 TYPE SET > RX-ANT Connectors
(00=Connect an receive antenna,
01=Connect an external device)
0276 see p. 13 ANTENNA MEMORY
(0.03 MHz to 1.60 MHz)
0277 see p. 13 ANTENNA MEMORY (1.60 MHz to
2.00 MHz)
0278 see p. 13 ANTENNA MEMORY (2.00 MHz to
6.00 MHz)
0279 see p. 13 ANTENNA MEMORY (6.00 MHz to
8.00 MHz)
0280 see p. 13 ANTENNA MEMORY (8.00 MHz to
11.00 MHz)
0281 see p. 13 ANTENNA MEMORY (11.00 MHz to
15.00 MHz)
0282 see p. 13 ANTENNA MEMORY (15.00 MHz to
20.00 MHz)
0283 see p. 13 ANTENNA MEMORY (20.00 MHz to
22.00 MHz)
0284 see p. 13 ANTENNA MEMORY (22.00 MHz to
26.00 MHz)
0285 see p. 13 ANTENNA MEMORY (26.00 MHz to
30.00 MHz)
0286 see p. 13 ANTENNA MEMORY (30.00 MHz to
45.00 MHz)
0287 see p. 13 ANTENNA MEMORY (45.00 MHz to
60.00 MHz)
0288 00 or 01 Temporary memory (TEMP-M) function
(00=OFF, 01=ON)
0289 00 ~ 02
Send the Antenna selection mode ([ANT] SW)
(00=OFF, 01=Manual, 02=Auto)
0290 00 ~ 09 NB depth
(00=1 to 09=10)
0291 0000 ~ 0255 NB width
(0000=1 to 0255=100)
0292 00 ~ 20 VOX delay
(00=0.0 sec. to 20=2.0 sec.; 0.1 sec steps)
0293 00 ~ 03 VOX voice delay
(00=OFF, 01=Short, 02=Mid, 03=Long)
0294 00 or 01 APF > TYPE
(00=SHARP, 01=SOFT)
0295 00 ~ 06 APF > AF LEVEL
(00=0 dB to 06=6 dB)
06 see p. 12 DATA mode with lter set
07 00 or 01 NTP server access
(00=Terminate, 01=Initiate)
08*
5
00 ~ 02 Read NTP server access result
(00=Accessing, 01=Succeeded, 02=Failed)
09 00 or 01 AF Mute
(00=OFF, 01=ON)
1B* 00 see p. 13 Repeater tone frequency
01 see p. 13 TSQL tone frequency
1C 00* 00 or 01 Ttransceiver's status
(00=RX, 01=TX)
*When “CI-V Output (for ANT)”
(Command: 1C 04) is set to “ON,”
automatically outputs when changed.
01* 00 ~ 02 Antenna tuner
(00=OFF, 01=ON, 02=Tune)
02* 00 or 01 Transmit frequency monitor (XFC)
(00=OFF, 01=ON)
03 see p. 10 Read transmit frequency
( When “CI-V Output (for ANT)”
(Command: 1C 04) is set to “ON,”
automatically outputs when changed.)
04* 00 or 01 CI-V Output (for ANT)
(00=OFF, 01=ON)
1A* 05 1A* 05
Remote control
8