Icom IC-905 Reference Guide

6
REMOTE CONTROL
Remote control (CI-V) information
D Command table
Cmd� Sub cmd� Data Description
1A* 05 SET > Function
00 38 00 ~ 05 Send/read the TX Delay (144M)
setting
( 00=OFF, 01=10 ms, 02=15 ms,
03=20 ms, 04=25 ms, 05=30 ms)
00 39 00 ~ 05 Send/read the TX Delay (430M)
setting
( 00=OFF, 01=10 ms, 02=15 ms,
03=20 ms, 04=25 ms, 05=30 ms)
00 40 00 ~ 05 Send/read the TX Delay (1200M)
setting
( 00=OFF, 01=10 ms, 02=15 ms,
03=20 ms, 04=25 ms, 05=30 ms)
00 41 00 ~ 05 Send/read the TX Delay (2400M)
setting
( 00=OFF, 01=10 ms, 02=15 ms,
03=20 ms, 04=25 ms, 05=30 ms)
00 42 00 ~ 05 Send/read the TX Delay (5600M)
setting
( 00=OFF, 01=10 ms, 02=15 ms,
03=20 ms, 04=25 ms, 05=30 ms)
00 43 00 ~ 05 Send/read the TX Delay (10G)
setting
( 00=OFF, 01=10 ms, 02=15 ms,
03=20 ms, 04=25 ms, 05=30 ms)
00 44 00 ~ 05 Send/read the Time-Out Timer
setting
( 00=OFF, 01=3 min, 02=5 min,
03=10 min, 04=20 min, 05=30 min)
00 45 00/01 Send/read the PTT Lock setting
( 00=OFF, 01=ON)
00 46 00/01 SPLIT >
Send/read the Quick SPLIT setting
( 00=OFF, 01=ON)
00 47 See p� 20� SPLIT >
Send/read the SPLIT Offset setting
00 48 00/01 SPLIT >
Send/read the SPLIT LOCK setting
( 00=OFF, 01=ON)
00 49 00/01
Send/read the Auto Repeater setting
( 00=OFF, 01=ON (DUP),
02=ON (DUP,TONE))
00 50 00 ~ 02 Send/read the RTTY Mark
Frequency setting
( 00=1275 Hz, 01=1615 Hz,
02=2125 Hz)
00 51 00 ~ 02 Send/read the RTTY Shift Width
setting
( 00=170 Hz, 01=200 Hz, 02=425 Hz)
00 52 00/01 Send/read the RTTY Keying
Polarity setting
( 00=Normal, 01=Reverse)
00 53 00 ~ 06 Send/read the ATV Audio Sub
Carrier Frequency setting
( 00=OFF, 01=4�5 MHz, 02=5�5 MHz,
03=6�0 MHz, 04=6�5 MHz,
05=7�02 MHz, 06=7�2 MHz)
00 54 00/01 SPEECH >
Send/read the SPEECH Language
setting
( 00=Japanese, 01=English)
Cmd� Sub cmd� Data Description
1A* 05 SET > Function
00 55 00/01
SPEECH >
Send/read the Alphabet setting
( 00=Normal, 01=Phonetic Code)
00 56 00/01
SPEECH >
Send/read the SPEECH Speed setting
( 00=Slow, 01=Fast)
00 57 00 ~ 02 SPEECH >
Send/read the RX Call Sign
SPEECH setting
( 00=OFF, 01=ON (Kerchunk),
02=ON (All))
00 58 00/01 SPEECH >
Send/read the RX>CS SPEECH setting
( 00=OFF, 01=ON)
00 59 00/01 SPEECH >
Send/read the MIC Up/Down
SPEECH setting
( 00=OFF, 01=ON)
00 60 00/01 SPEECH >
Send/read the S-Level SPEECH setting
( 00=OFF, 01=ON)
00 61 00/01
SPEECH >
Send/read the MODE SPEECH setting
( 00=OFF, 01=ON)
00 62 00 00 ~ 02 55
SPEECH >
Send/read the SPEECH Level setting
( 00 00=0% ~ 02 55=100%)
00 63 00/01 Send/read the [SPEECH/LOCK]
Switch setting
( 00=SPEECH/LOCK,
01=LOCK/SPEECH)
00 64 00/01
Send/read the Lock Function setting
( 00=MAIN DIAL, 01=PANEL)
00 65 00/01 Send/read the Memo Pad Quantity
setting
( 00=5 ch, 01=10 ch)
00 66 00/01
Send/read the Function of Touch
for 1 sec MHz Digits setting
( 00=Band Stacking Register,
01=1 MHz Step Tuning)
00 67 00 ~ 02
Send/read the MAIN DIAL Auto TS
setting
(00=OFF, 01=Low, 02=High)
00 68 00/01
Send/read the MIC Up/Down Speed
setting
(00=Slow, 01=Fast)
00 69 00/01 Send/read the AFC Limit setting
(00=OFF, 01=ON)
00 70 00 ~ 02 Send/read the
[NOTCH] Switch
(SSB) setting
(00=Auto, 01=Manual, 02=Auto/Manual)
00 71 00 ~ 02 Send/read the [NOTCH] Switch
(AM) setting
(00=Auto, 01=Manual, 02=Auto/Manual)
00 72 00/01 Send/read the SSB/CW
Synchronous Tuning setting
(00=OFF, 01=ON)
00 73 00/01
Send/read the CW Normal Side setting
(00=LSB, 01=USB)

Icom IC-905 Specifications

General

LAN Port	Yes
Power Supply	13.8 V DC
Modes	FM, SSB, CW, AM
Display	4.3-inch color TFT touch screen
GPS	Yes
USB Port	Yes
Antenna Connector	N-type