To Next PageTo Next PageWhy can't I contact another station with my Icom Transceiver?
If you are unable to contact another station using your Icom Transceiver, it might be because a different tone is selected with tone/DTCS squelch. Check the tone/DTCS using tone scan.
What to do if Icom Transceiver frequency cannot be set?
If you're unable to set the frequency on your Icom Transceiver, the lock function might be activated. To deactivate it, push the [MENU/ ] button for 1 second. Alternatively, you might be in Memory mode or have a call channel selected; push [VFO] to set VFO mode.
Why Icom IC-92A program scan function can not start?
If the program scan function on your Icom Transceiver won't start, it could be because Memory mode or call channel is selected. Push [VFO] to set VFO mode. Another reason might be that the same frequencies are programmed for both “?A” and “?B” of PROGRAM-CH; program different frequencies in “?A” and “?B” respectively.
How to unlock the frequency setting on my Icom Transceiver?
If you're unable to set the frequency on your Icom Transceiver, there are a couple of possibilities. The lock function may be activated; push [MENU/ ] for 1 second to cancel the function. Alternatively, you might have Memory mode or call channel selected; push [VFO] to set VFO mode.
Why won't the program scan function start on my Icom Transceiver?
If the program scan function won't start on your Icom Transceiver, it could be because memory mode or call channel is selected; push [VFO] to set VFO mode. Another possibility is that the same frequencies are programmed for both “?A” and “?B” of PROGRAM-CH; program different frequencies in “?A” and “?B” respectively.
How to fix Icom Transceiver when no power comes ON?
If your Icom Transceiver isn't powering on, the batteries might be exhausted. Replace them or charge the battery pack. Also, verify the battery polarity to ensure it's correct.
Why does the BC-177 LED blink orange when charging my Icom Transceiver battery?
If you can't charge the battery with BC-177 and the LED blinks orange, it may be because the transceiver's power is ON. Turn the transceiver’s power OFF, or insert only the battery pack into the BC-177 to charge it. Another reason might be that the battery pack has fault electric discharge. The battery pack is charged alone (without the trans- ceiver) or regular charge is carried out.
What causes an erroneous frequency display on an Icom Transceiver?
If the displayed frequency on your Icom Transceiver is incorrect, it could be due to two reasons: The CPU may have malfunctioned; try resetting the transceiver. Alternatively, external factors might have caused a fault; remove and re-attach the battery pack or battery case.
What to do if no sound comes from the Icom Transceiver speaker?
If you're not getting any sound from the speaker of your Icom Transceiver, there are a couple of things to check. First, the volume level might be too low. Rotate the [VOL] knob to a suitable level. Second, if you have an external speaker connected with OPC-1797, verify that the connection of the external speaker or OPC-1797 is correct.
Why Icom IC-92A memory scan function can not start?
If the memory scan function on your Icom Transceiver isn't starting, it could be because VFO mode or a call channel is selected. Push [MR] to set memory mode. Also, ensure that you have programmed more than 2 memory channels, as the scan won't start if only one is programmed.
General| Frequency Range | 144-148 MHz, 430-450 MHz |
|---|---|
| IP Rating | IP54 |
| Waterproof | Yes |
| GPS | Yes |
| Bluetooth | No |
| Modulation | FM, AM |
| Receiver Sensitivity | 0.16 μV (12 dB SINAD) |
| Operating Voltage | 7.4V DC |
