To Next PageTo Next Page
Need help?Do you have a question about the Icom IC-V8 and is the answer not in the manual?
General| Frequency Range | 136-174 MHz |
|---|---|
| Power Output | 5.5 W |
| Mode | FM |
| Receiver Sensitivity | 0.16 μV (12dB SINAD) |
| Channel Spacing | 12.5/25 kHz |
| Voltage | 7.2 V DC |
Guidelines to ensure RF electromagnetic energy exposure stays within FCC allowable limits.
A brief introduction to the transceiver and its design.
Key advice for reading and saving the instruction manual.
Definitions for WARNING, CAUTION, and NOTE symbols used in the manual.
Essential safety guidelines for operating the transceiver and charging batteries.
Detailed description of the transceiver's physical controls, buttons, and connection points.
Explains the function of each key on the transceiver's keypad.
Explanation of the various indicators and readouts on the transceiver's display screen.
Instructions on how to attach accessories like the antenna and belt clip.
Step-by-step guide for replacing the battery pack on the transceiver.
Important safety warnings and precautions related to handling and using battery packs.
Instructions for regular and rapid charging using various Icom chargers.
Important notes for optimal battery charging and maintaining battery life.
Instructions for installing alkaline batteries into the optional BP-208 battery case.
How to turn the transceiver on and off using the power switch.
Step-by-step guide to setting an operating frequency using the keypad or other methods.
Instructions on how to adjust the audio and squelch levels for optimal reception.
Procedures for receiving signals and transmitting using the transceiver.
How to select and use stored memory channels and the dedicated call channel.
How to activate and deactivate the key lock function to prevent accidental changes.
How to change the transceiver's display mode (frequency, channel name).
Introduction to repeater operation and frequency shifting principles.
How to set the frequency offset for repeater communication.
How to set subaudible (CTCSS/DTCS) tones required by repeaters.
Details on DTMF Tones, 1750 Hz TONE, and using tone scan.
How the auto repeater function automatically adjusts settings based on frequency.
Overview of memory channels and their contents.
Step-by-step instructions for programming memory and call channels.
How to assign names to memory channels for easier identification.
How to transfer memory or call channel contents to VFO or other memory channels.
Procedure for clearing stored memory channels.
How to program DTMF codes into the transceiver's memory.
How to transmit DTMF codes using memory channels or manually.
How to adjust the DTMF transmission speed for compatible repeaters.
Overview of different scan modes: Programmed Scan, Memory (Skip) Scan, and Priority Watch.
Detailed instructions for using the programmed scan feature.
How to perform memory scans and set channels to skip.
How to monitor priority channels while operating on a VFO frequency.
How to set the scan resume behavior (pause or timer).
How to use tone squelch to receive calls only from stations with matching subaudible tones.
Steps to set subaudible tones for tone squelch and pocket beep operations.
How to use the pocket beep function for receiving alerts from specific stations.
How to scan for and identify repeater tone frequencies.
Overview of the pager function, requiring UT-108, for selective calling.
How to program ID codes and group codes for pager and code squelch functions.
Explanation of how 'Receive accept' and 'Receive inhibit' settings work.
How to initiate a page to a specific station and handle answer backs.
How the transceiver behaves when receiving personal or group calls.
How to use code squelch to receive calls only from stations with known codes.
How to enter and navigate the transceiver's set mode for various configurations.
How to select tuning step size and set scan pause duration.
How to configure function key timers and control the LCD backlight.
How to manage transmission permissions and program pager/squelch channels.
How to access and use the initial set mode for seldom-changed settings.
How to enable key-touch beeps and set the time-out timer.
How auto repeater and auto power-off functions operate.
How to configure repeater lockout settings (repeater, busy, or off).
How to set squelch delay and adjust DTMF transmission speeds.
How to assign functions to the dial and select display types.
How to adjust LCD contrast and select power save duty cycles.
How tuning speed acceleration works.
How to enable microphone simple mode for key function assignments.
How to perform a CPU reset to restore default settings.
How to transfer data between transceivers using a cloning cable.
How to clone data from a PC using cloning software.
Instructions for installing the optional UT-108 DTMF decoder unit.
General specs: frequency range, temp, power requirements, dimensions, weight.
Technical specifications for the transmitter section.
Technical specifications for the receiver section.
List of available battery packs with their specifications.
List of available chargers and their charging times.
Information about the UT-108 DTMF decoder unit.
List of other optional accessories like microphones and cables.
