To Next PageTo Next PageWhy Icom IC-92AD Transceiver is not transmitting?
If your Icom Transceiver isn't transmitting, it could be due to exhausted batteries. Try replacing the batteries or charging the battery pack. Also, ensure that the set frequency is within the 144/440 MHz amateur bands; if it's outside, reset it accordingly.
What to do if Icom IC-92AD Transceiver frequency cannot be set?
If you're unable to set the frequency on your Icom Transceiver, the lock function might be activated. To deactivate it, push the [MENU/ ] button for 1 second. Alternatively, you might be in Memory mode or have a call channel selected; push [VFO] to set VFO mode.
Why Icom Transceiver program scan function can not start?
If the program scan function on your Icom Transceiver won't start, it could be because Memory mode or call channel is selected. Push [VFO] to set VFO mode. Another reason might be that the same frequencies are programmed for both “?A” and “?B” of PROGRAM-CH; program different frequencies in “?A” and “?B” respectively.
How to unlock the frequency setting on my Icom Transceiver?
If you're unable to set the frequency on your Icom Transceiver, there are a couple of possibilities. The lock function may be activated; push [MENU/ ] for 1 second to cancel the function. Alternatively, you might have Memory mode or call channel selected; push [VFO] to set VFO mode.
Why won't the program scan function start on my Icom Transceiver?
If the program scan function won't start on your Icom Transceiver, it could be because memory mode or call channel is selected; push [VFO] to set VFO mode. Another possibility is that the same frequencies are programmed for both “?A” and “?B” of PROGRAM-CH; program different frequencies in “?A” and “?B” respectively.
How to fix Icom IC-92AD when no power comes ON?
If your Icom Transceiver isn't powering on, the batteries might be exhausted. Replace them or charge the battery pack. Also, verify the battery polarity to ensure it's correct.
Why no sound from Icom IC-92AD Transceiver speaker?
If you're not getting any sound from your Icom Transceiver's speaker, first check the volume level and rotate the [VOL] knob to a suitable level. Also, verify that the correct tone is selected if you're using tone/DTCS squelch by checking the tone using tone/DTCS scan.
What causes Icom IC-92AD no contact with another station?
If you cannot contact another station using your Icom Transceiver, it might be because a different tone is selected with tone/DTCS squelch. Check the tone/DTCS using tone scan.
What to do if Icom IC-92AD Transceiver displayed frequency is erroneous?
If the displayed frequency on your Icom Transceiver is incorrect, it could be due to a CPU malfunction; try resetting the transceiver. It might also be caused by external factors, in which case, remove and re-attach the battery pack or battery case.
Why Icom IC-92AD memory scan function can not start?
If the memory scan function on your Icom Transceiver isn't starting, it could be because VFO mode or a call channel is selected. Push [MR] to set memory mode. Also, ensure that you have programmed more than 2 memory channels, as the scan won't start if only one is programmed.
Warns about radio frequency energy emitted by the device and advises consulting FCC guidelines.
Advises against holding the transceiver close to the body during transmission for optimal performance.
Warns against using high volume with audio accessories to prevent hearing damage.
Prohibits transceiver use while driving, emphasizing the need for full attention to safe operation.
Step-by-step instructions for using repeaters, including setting frequencies and shift directions.
Step-by-step guide to setting your personal call sign for DV mode.
Instructions for programming the call signs of other stations for DV mode.
Instructions for programming repeater call signs (RPT1/RPT2) for DV operation.
Step-by-step instructions for programming frequencies and settings into memory channels.
How to assign memory channels to banks for easier organization and management.
How to assign custom alphanumeric names to memory channels, banks, and scans.
How to erase stored memory channel data.
How to clear or move programmed memory channels between banks.
How to perform full band scan, selected band scan, and programmed scans.
How to set the frequency limits (scan edges) for programmed scans.
How to perform memory scans to search programmed memory channels.
How to perform scans across memory banks.
Continues the guide on setting skip conditions for channels and frequencies.
Settings for when the scan resumes after pausing.
How to set the duration for scan pauses when signals are received.
How to set the time before a scan resumes after a signal disappears.
Describes the three available types of priority watch for monitoring frequencies.
How to activate and use the priority watch function to monitor channels.
Detailed explanation of various set mode items like Auto Power OFF, Power Save, and Attenuator.
How to enable or disable the PTT lock function to prevent accidental transmissions.
List of settings available within the DV Set Mode.
How to set the transmission of GPS data from a connected receiver ON or OFF.
How to enable or disable the break-in function for conversations.
List of settings available within the Scan Set Mode.
How to enable and configure the memory bank link function for continuous bank scanning.
How to select DTCS codes for DTCS squelch or beep operations.
How to select DTMF codes for transmission via keypad presses.
List of settings available within the Sounds Set Mode.
How to set the transceiver to automatically turn OFF after a specified period.
How to enable or disable the busy lockout function to prevent transmission during reception.
How to configure the automatic reply feature for individual station calls.
How to enable or disable the EMR (Emergency) communication mode.
How to set priority watch (OFF, ON, BELL) for monitoring frequencies.
How to enable and configure the program scan link function for continuous program scanning.
How to adjust the beep tone level within 39 levels.
How to enable and configure the power save feature to conserve battery power.
How to set the transceiver to automatically turn ON after a specified period.
How to set the time-out timer to limit continuous transmission duration.
How to set digital codes for digital code squelch operations.
How the transceiver automatically writes received station call signs to 'UR'.
How to configure the scan pause timer duration (2-20 sec or HOLD).
How to adjust the DTMF transmission speed.
How to turn the key-touch beep function ON or OFF.
How to turn the attenuator ON or OFF to reduce strong signal distortion.
How to configure data transmission in DV mode via the [DATA] jack.
How the transceiver automatically writes repeater call signs to 'RPT1'/'RPT2'.
How to configure the scan resume timer duration (0-5 sec or HOLD).
How to turn the scan stop beep function ON or OFF.
How to set the offset frequency for duplex (repeater) operation.
How to set the subaudible tone frequency for repeater access.
How to set the tone frequency for tone squelch or pocket beep.
Step-by-step guide to programming DTMF codes into memory channels.
How to transmit DTMF codes by pushing the SQL switch.
How to transmit DTMF codes directly via keypad while transmitting.
Information on tone frequencies and DTCS codes for squelch and beep functions.
Continues the guide on setting digital codes for squelch and beep functions.
How the pocket beep alert feature works using tones or DTCS codes.
How to perform a tone scan to detect subaudible tones or DTCS codes.
Continues the description of the pocket beep function, including receiving signals.
Continues the description of the tone scan operation, including programming decoded data.
Explains how the power save function reduces battery consumption by adjusting receive/off cycles.
How to configure the transceiver to automatically turn OFF after a set period.
How to copy transceiver data (settings and contents) to another IC-92AD.
Procedures for resetting the transceiver's settings to default values.
How to set the polarity for DTCS codes (Normal or Reverse).
How to transmit codes stored in DTMF memory.
How to erase unwanted DTMF memory entries.
How to adjust the DTMF transmission speed (100-500 msec).
How to configure DTCS codes for DTCS squelch or beep operations.
Continues the explanation of DTCS polarity settings for TX and RX.
How to set the transceiver to automatically turn ON after a specified period.
How to perform a full reset of the transceiver's CPU and all programmed contents.
How to transmit DTMF codes directly via keypad while in VFO mode.
How to set digital codes and call signs for digital squelch or beep.
How the key lock function prevents accidental frequency changes and function access.
How the time-out timer limits continuous transmission duration and provides a warning.
How to enable or disable the PTT lock function to prevent accidental transmissions.
Warns about radio frequency energy emitted by the device and advises consulting FCC guidelines.
Advises against holding the transceiver close to the body during transmission for optimal performance.
Warns against using high volume with audio accessories to prevent hearing damage.
Prohibits transceiver use while driving, emphasizing the need for full attention to safe operation.
Step-by-step instructions for using repeaters, including setting frequencies and shift directions.
Step-by-step guide to setting your personal call sign for DV mode.
Instructions for programming the call signs of other stations for DV mode.
Instructions for programming repeater call signs (RPT1/RPT2) for DV operation.
Step-by-step instructions for programming frequencies and settings into memory channels.
How to assign memory channels to banks for easier organization and management.
How to assign custom alphanumeric names to memory channels, banks, and scans.
How to erase stored memory channel data.
How to clear or move programmed memory channels between banks.
How to perform full band scan, selected band scan, and programmed scans.
How to set the frequency limits (scan edges) for programmed scans.
How to perform memory scans to search programmed memory channels.
How to perform scans across memory banks.
Continues the guide on setting skip conditions for channels and frequencies.
Settings for when the scan resumes after pausing.
How to set the duration for scan pauses when signals are received.
How to set the time before a scan resumes after a signal disappears.
Describes the three available types of priority watch for monitoring frequencies.
How to activate and use the priority watch function to monitor channels.
Detailed explanation of various set mode items like Auto Power OFF, Power Save, and Attenuator.
How to enable or disable the PTT lock function to prevent accidental transmissions.
List of settings available within the DV Set Mode.
How to set the transmission of GPS data from a connected receiver ON or OFF.
How to enable or disable the break-in function for conversations.
List of settings available within the Scan Set Mode.
How to enable and configure the memory bank link function for continuous bank scanning.
How to select DTCS codes for DTCS squelch or beep operations.
How to select DTMF codes for transmission via keypad presses.
List of settings available within the Sounds Set Mode.
How to set the transceiver to automatically turn OFF after a specified period.
How to enable or disable the busy lockout function to prevent transmission during reception.
How to configure the automatic reply feature for individual station calls.
How to enable or disable the EMR (Emergency) communication mode.
How to set priority watch (OFF, ON, BELL) for monitoring frequencies.
How to enable and configure the program scan link function for continuous program scanning.
How to adjust the beep tone level within 39 levels.
How to enable and configure the power save feature to conserve battery power.
How to set the transceiver to automatically turn ON after a specified period.
How to set the time-out timer to limit continuous transmission duration.
How to set digital codes for digital code squelch operations.
How the transceiver automatically writes received station call signs to 'UR'.
How to configure the scan pause timer duration (2-20 sec or HOLD).
How to adjust the DTMF transmission speed.
How to turn the key-touch beep function ON or OFF.
How to turn the attenuator ON or OFF to reduce strong signal distortion.
How to configure data transmission in DV mode via the [DATA] jack.
How the transceiver automatically writes repeater call signs to 'RPT1'/'RPT2'.
How to configure the scan resume timer duration (0-5 sec or HOLD).
How to turn the scan stop beep function ON or OFF.
How to set the offset frequency for duplex (repeater) operation.
How to set the subaudible tone frequency for repeater access.
How to set the tone frequency for tone squelch or pocket beep.
Step-by-step guide to programming DTMF codes into memory channels.
How to transmit DTMF codes by pushing the SQL switch.
How to transmit DTMF codes directly via keypad while transmitting.
Information on tone frequencies and DTCS codes for squelch and beep functions.
Continues the guide on setting digital codes for squelch and beep functions.
How the pocket beep alert feature works using tones or DTCS codes.
How to perform a tone scan to detect subaudible tones or DTCS codes.
Continues the description of the pocket beep function, including receiving signals.
Continues the description of the tone scan operation, including programming decoded data.
Explains how the power save function reduces battery consumption by adjusting receive/off cycles.
How to configure the transceiver to automatically turn OFF after a set period.
How to copy transceiver data (settings and contents) to another IC-92AD.
Procedures for resetting the transceiver's settings to default values.
How to set the polarity for DTCS codes (Normal or Reverse).
How to transmit codes stored in DTMF memory.
How to erase unwanted DTMF memory entries.
How to adjust the DTMF transmission speed (100-500 msec).
How to configure DTCS codes for DTCS squelch or beep operations.
Continues the explanation of DTCS polarity settings for TX and RX.
How to set the transceiver to automatically turn ON after a specified period.
How to perform a full reset of the transceiver's CPU and all programmed contents.
How to transmit DTMF codes directly via keypad while in VFO mode.
How to set digital codes and call signs for digital squelch or beep.
How the key lock function prevents accidental frequency changes and function access.
How the time-out timer limits continuous transmission duration and provides a warning.
How to enable or disable the PTT lock function to prevent accidental transmissions.
General| Receiver System | Double Conversion Superheterodyne |
|---|---|
| GPS Receiver | Built-in |
| D-STAR | Yes |
| Frequency Range | 144-148 MHz, 430-450 MHz |
| Modulation | FM, D-STAR |
| Operating Voltage | 7.4V DC |
| Current Drain | 1.5A |
| Waterproof | IPX7 |
