What to do if the displayed channel cannot be changed on Icom IC-M73EURO Transceiver?
If you cannot change the displayed channel on your Icom Transceiver, the lock function may be activated. To deactivate it, push [H/L•LOCK] for 1 second.
Why is there no sound coming from my Icom IC-M73EURO Transceiver speaker?
If you're not getting any sound from your Icom Transceiver speaker, here are a few things to check: * The squelch level might be set too high. Try adjusting it to the threshold point. * The volume could be too low. Rotate the [VOL] knob to increase the volume. * If the speaker got wet, hold down [F] to drain any water. * Also, check the [SP MIC] connector for moisture and dry it if necessary.
Why can't I transmit or select high power on my Icom IC-M73EURO?
If you're unable to transmit or select high power on your Icom Transceiver, it could be due to several reasons: * Some channels are designated for low power or receive-only. Try switching to a different channel. * The battery may be low. Recharge the battery pack. * The battery voltage may be incorrect. Verify the battery voltage is correct. * The output power might be set to low. Press [H/L•LOCK] to select high power. * The transceiver could be overheating. Turn it OFF and let it cool down at room temperature.
How to fix an Icom IC-M73EURO that does not turn on?
If your Icom Transceiver isn't turning on, the issue might be: * A depleted battery. Recharge the battery pack. * A bad connection to the battery pack. Check the connection to the transceiver to ensure it's secure.
Why is the “CHARGE” comment blinking on my Icom Transceiver?
If the “CHARGE” comment is blinking on your Icom Transceiver, it means the connected battery is depleted. Recharge the battery pack.
How to turn on the beep sound on Icom IC-M73EURO Transceiver?
If you are not hearing any beeps on your Icom Transceiver, the beep tones may be turned OFF. To turn them ON, go to the SET mode and set the beep tones to ON (Fix Beep/Preset).
Why won't the scan start on my Icom IC-M73EURO?
If the scan function isn't starting on your Icom Transceiver, it could be because you haven't programmed any favorite (TAG) channels. Set the channels you want to scan as 'Favorite (TAG)' channels.
Why isn't my Icom IC-M73EURO recording weak signals with the automatic recording function?
If your Icom Transceiver isn't recording weak signals using the automatic recording function, the automatic recording threshold level might be set too deep. Try setting it to shallow.
General| Brand | Icom |
|---|---|
| Model | IC-M73EURO |
| Category | Transceiver |
| Language | English |
Crucial instructions to read carefully before using the transceiver.
Defines specific terms used throughout the manual.
Highlights the main features of the IC-M73/IC-M73EURO transceiver.
Lists important safety warnings and precautions for using the transceiver.
Warns about RF energy exposure and provides guidelines for safe operation.
Discusses potential interference and compatibility issues during transmission.
Information regarding compliance with FCC rules for unintentional radiators.
Lists country codes according to ISO 3166-1 standard.
Procedure for making distress calls via Channel 16.
Advice on cleaning and drying the transceiver after saltwater exposure.
Rules for call priorities, privacy, and required radio licenses.
Lists and illustrates accessories included with the transceiver.
Instructions on attaching the flexible antenna and handstrap.
Instructions for attaching the battery pack and belt clip.
Identifies and explains the function of front, top, and side panel controls.
Explains keys for channel selection, scan, function modes, and power.
Details connectors and indicators for transmit power.
Explains the various icons displayed on the transceiver's screen.
Explains icons related to channels, status, and signal reception.
How to select Channel 16 and the Call Channel.
Steps to select channels and switch between channel groups.
How to select and use weather channels for broadcasts.
How to adjust squelch level and transmit power.
How to program call channels, use lock and monitor functions.
Step-by-step guide to adjust squelch and use AquaQuake function.
Explanation of Normal and Priority scan modes.
How to set favorite channels and initiate a scan.
Explains and details the operation of Dualwatch and Tri-watch.
Overview of available functions and how to enter the mode.
How to use manual and automatic recording features.
How to play back recorded audio and name channels.
How to set opening comments and program ATIS codes.
How to control the display backlight for nighttime use.
Steps to enter SET mode and a list of all configurable settings.
Configuration for beep tones, weather alerts, and scan behavior.
Settings for scan, watch modes, key actions, and backlight.
Settings for display, scrolling, and power management.
Configuration for noise cancellation, bass boost, and auto recording threshold.
Critical warnings for battery handling and charging safety.
Information on installing and using supplied and optional chargers.
Instructions for optional belt clips and speaker-microphones.
Details on optional battery packs, chargers, cables, and antennas.
A table listing common problems, their causes, solutions, and references.
General, transmitter, and receiver specifications for the IC-M73.
General, transmitter, and receiver specifications for the IC-M73EURO.
Specific technical details for the Australian version of IC-M73EURO.
List of international VHF marine channels and their frequencies.
List of USA VHF marine channels for the UK version.
List of VHF marine channels for Australia.
To Next Page
