To Next Page
C
Cameron HardySep 23, 2025
How to enable beep sounds on Icom IC-M71?
- HhjohnstonSep 23, 2025
If there are no beep sounds on your Icom Transceiver, the beep tones may be turned OFF. Set the beep tones to ON (Fix Beep/User Beep) in the SET mode.
How to enable beep sounds on Icom IC-M71?
If there are no beep sounds on your Icom Transceiver, the beep tones may be turned OFF. Set the beep tones to ON (Fix Beep/User Beep) in the SET mode.
How to unlock Icom Transceiver channel?
If the displayed channel on your Icom Transceiver cannot be changed, it's likely that the lock function is activated. To cancel this function, push [H/L•LOCK] for 1 second.
How to fix Icom IC-M71 Transceiver that does not turn on?
If your Icom Transceiver isn't turning on, the battery might be depleted. Try recharging the battery pack. Also, check the connection to the transceiver to ensure it's properly connected.
What to do if there is no sound from the Icom Transceiver speaker?
If you're not getting any sound from your Icom Transceiver's speaker, here are a few things to check: * The squelch level might be too tight. Try setting the squelch to the threshold point. * The volume level could be too low. Rotate [VOL] to adjust it to a suitable level. * If the speaker has been exposed to water, push and hold both [16•C] and [H/L•LOCK] to drain the water. * If water has entered the [SP MIC] connector, dry the connector.
Why Icom IC-M71 Transceiver transmitting is impossible?
If you're unable to transmit or select high power on your Icom Transceiver, it could be due to several reasons: 1. Some channels are set for low power or receive only, so try changing channels. 2. The battery may be exhausted; recharge the battery pack. 3. Verify the battery voltage is correct in case the battery is overcharged. 4. The output power might be set to low; push [H/L•LOCK] to select high power.
What to do if my Icom IC-M71 does not turn ON?
If your Icom Transceiver doesn't turn on, the battery may be depleted, so recharge the battery pack. Alternatively, there might be a bad connection to the battery pack, so check the connection to the transceiver.
Why is there no sound coming from my Icom IC-M71 speaker?
If no sound is coming from your Icom Transceiver speaker, there could be several reasons: * The squelch level might be set too high. Try setting the squelch to the threshold point. * The volume level might be too low. Rotate the [VOL] knob to increase the volume to a suitable level. * The speaker might have been exposed to water. Push and hold both [16•C] and [H/L•LOCK] to drain any water from the speaker. * Water might have entered the [SP MIC] connector. Ensure this connector is dry.
How to turn on beeps on Icom Transceiver?
If there are no beeps on your Icom Transceiver, the beep tones are likely turned OFF. Set the beep tones to ON (Fix Beep/User Beep) in the SET mode.
What to do if Icom Transceiver has no sound from the speaker?
If there is no sound from the Icom Transceiver's speaker, there could be several reasons: * The squelch level might be too tight. Try setting the squelch to the threshold point. * The volume level might be too low. Rotate the [VOL] knob to set a suitable level. * The speaker may have been exposed to water. Push and hold both [16•C] and [H/L•LOCK] to drain water from the speaker. * Water may have entered the [SP MIC] connector. Ensure you dry the [SP MIC] connector.
What does self check error (Battery voltage) mean on Icom IC-M71 Transceiver?
If you're getting a self-check error related to battery voltage on your Icom Transceiver, it indicates that the connected battery pack’s voltage is more than 11 V. Verify the battery voltage is correct.
General| Type | Handheld VHF Marine Transceiver |
|---|---|
| Frequency Range | 156.000 - 163.425 MHz |
| Channels | USA: 88, International: 28, Canadian: 14, Weather: 10 |
| Power Output | 5W / 1W |
| Power Supply Requirement | 7.2V DC |
| RF Output Power | 5W / 1W |
| Modulation System | FM |
| Waterproof Rating | IPX7 |
| Spurious Emissions | -70 dB or less |
| Frequency Stability | ±10 ppm |
| Audio Output Power | 500 mW (at 10% distortion, 8 Ω) |
| Sensitivity (at 12 dB SINAD) | 0.25 μV |
| Intermodulation Rejection Ratio | 70 dB |
| Spurious Response Rejection Ratio | 70 dB |
| Adjacent Channel Selectivity | 70 dB |
| Mode | Simplex |
| Battery Life | Approx. 10 hours (5W/5-5-90 duty cycle) |
| Type of Emission | 16K0G3E |
