What to do if Icom Transceiver self check error shows temperature?
If your Icom Transceiver displays a self-check error related to temperature, it indicates that the temperature is outside of –35°C to +73°C (approx.). Leave the transceiver at room temperature for a while and then turn the power ON to check if the internal temperature has returned to normal.
Why Icom Transceiver scan does not start?
If the scan function on your Icom Transceiver does not start, it might be because “TAG” channels are not programmed. Set the desired channels as “TAG” channels.
What to do if Icom Transceiver self check error shows battery voltage?
If your Icom Transceiver shows a self-check error related to battery voltage, it means the connected battery pack’s voltage is more than 11 V. Verify that the battery voltage is correct.
How to unlock channel change on Icom Transceiver?
If you can't change the displayed channel on your Icom Transceiver, the lock function may be activated. Push [H/L•LOCK] for 1 second to cancel the function.
Why Icom Transceiver transmitting is impossible, or high power can not be selected?
If your Icom Transceiver is unable to transmit or high power cannot be selected, it could be due to the following reasons: * Some channels are set for low power or receive only. Try changing channels. * The battery is exhausted. Recharge the battery pack. * The battery is overcharged. Verify the battery voltage is correct. * The output power is set to low. Push [H/L•LOCK] to select high power.
What to do if Icom Transceiver has no sound from the speaker?
If there is no sound from the Icom Transceiver's speaker, there could be several reasons: * The squelch level might be too tight. Try setting the squelch to the threshold point. * The volume level might be too low. Rotate the [VOL] knob to set a suitable level. * The speaker may have been exposed to water. Push and hold both [16•C] and [H/L•LOCK] to drain water from the speaker. * Water may have entered the [SP MIC] connector. Ensure you dry the [SP MIC] connector.
What does self check error (Temperature) mean on Icom Transceiver?
If your Icom Transceiver displays a self-check error related to temperature, it means the temperature is outside of –35°C to +73°C (approx.). Leave the transceiver at room temperature for a while and then turn the power ON to check if the internal temperature has returned to normal.
What does self check error (Battery voltage) mean on Icom IC-M71 Transceiver?
If you're getting a self-check error related to battery voltage on your Icom Transceiver, it indicates that the connected battery pack’s voltage is more than 11 V. Verify the battery voltage is correct.
How to enable beeps on Icom IC-M71?
If you're not hearing any beeps from your Icom Transceiver, the beep tones may be turned OFF. Set the beep tones to ON (Fix Beep/User Beep) in the SET mode.
Why doesn't the scan start on my Icom IC-M71 Transceiver?
If the scan function isn't starting on your Icom Transceiver, it's possible that "TAG" channels are not programmed. Set the desired channels as “TAG” channels.
General| Type | Handheld VHF Marine Transceiver |
|---|---|
| Frequency Range | 156.000 - 163.425 MHz |
| Channels | USA: 88, International: 28, Canadian: 14, Weather: 10 |
| Power Output | 5W / 1W |
| Power Supply Requirement | 7.2V DC |
| RF Output Power | 5W / 1W |
| Modulation System | FM |
| Waterproof Rating | IPX7 |
| Spurious Emissions | -70 dB or less |
| Frequency Stability | ±10 ppm |
| Audio Output Power | 500 mW (at 10% distortion, 8 Ω) |
| Sensitivity (at 12 dB SINAD) | 0.25 μV |
| Intermodulation Rejection Ratio | 70 dB |
| Spurious Response Rejection Ratio | 70 dB |
| Adjacent Channel Selectivity | 70 dB |
| Mode | Simplex |
| Battery Life | Approx. 10 hours (5W/5-5-90 duty cycle) |
| Type of Emission | 16K0G3E |
To Next Page
