What does it mean if “DV” and “FM” icons alternately blink on Icom ID-5100A?
If the “DV” and “FM” icons alternately blink on your Icom Transceiver, it means that while in the DV mode, an FM signal is being received. Wait a while, and try it again.
Why does my Icom Transceiver reply 'RX' or 'RPT?' and the access repeater's call sign after I transmit?
If your Icom Transceiver replies with ‘RX’ or ‘RPT?’ followed by the access repeater’s call sign after you transmit, it could be due to issues with your call sign. Ensure that your call sign is correctly set in your transceiver. Also, verify that your call sign is registered on a trust server through a D-STAR repeater, or confirm its registration.
What to do if Icom ID-5100A replies 'RPT?' and call sign of the destination repeater after transmitting?
If, after transmitting, the repeater replies 'RPT?' and the call sign of the destination repeater, it means the repeater cannot connect to the destination repeater. Check the repeater setting, or the repeater might be busy. If the repeater is busy, wait for a while, and then try again.
What to do if Icom ID-5100A replies 'RPT?' and its call sign after I transmit?
If, after you transmit, the access repeater replies ‘RPT?’ and its call sign, the call sign of the destination repeater is wrong. Correctly set the destination repeater call sign.
How to fix a simplex operation that cannot be made in the DR screen of Icom ID-5100A Transceiver?
If a simplex operation cannot be made in the DR screen on your Icom Transceiver, it means a repeater frequency is programmed. Set a simplex frequency.
What to do if Icom Transceiver replies ‘RPT?’ and call sign of the destination repeater after my call?
If your Icom Transceiver replies with ‘RPT?’ and the call sign of the destination repeater after your call, it indicates that the repeater cannot connect to the destination repeater. To solve this, check the repeater setting. Alternatively, the repeater may be busy, so wait for a while and try again.
Why Icom ID-5100A Transceiver DR screen will not appear even holding down [DR]?
If the DR screen doesn't appear even when holding down [DR] on your Icom Transceiver, it could be due to the absence of a repeater list in your radio. To resolve this, reload the repeater list using the SD card. Alternatively, you can enter the Repeater list data directly into the transceiver.
What to do if Icom ID-5100A Transceiver repeater does not return a status reply after my call?
If the repeater doesn't return a status reply after your call on your Icom Transceiver, it could be due to several reasons. First, the repeater setting might be wrong, so select the correct repeater. Second, your transmission might not have reached the repeater; in this case, correct the repeater frequency, frequency offset, or duplex setting. Also, try again when you are closer to the repeater or try to access another repeater.
Why does 'L' appear on my Icom ID-5100A Transceiver and the audio is interrupted?
If the Icom Transceiver displays 'L' on the LCD and the received audio is interrupted, it's likely due to packet loss from a network error during internet reception. The suggested solution is to wait a while and try again.
How to solve the issue when the received call sign does not set to the destination call sign to make a call back on Icom ID-5100A?
If, even when holding down [RX>CS], the received call sign does not set to the destination call sign to make a call back on your Icom Transceiver, the transceiver did not correctly receive the call sign data. Try it again after the transceiver has correctly received the call sign.
Manages memory channels and call channels for radio operations.
Configures scan settings for searching frequencies and memory channels.
Manages GPS settings, position, and logging functions.
Controls various operational functions like squelch and PTT settings.
Quick menu items selectable in VFO mode for frequency tuning.
Quick menu items selectable in Memory Recall (MR) mode.
Quick menu items selectable in Call Channel mode.
Quick menu items selectable for the Digital Repeater (DR) function.
Explains the touch-sensitive areas on the display for various operations.
Details short touch and long touch operations and their feedback.
Covers selection between single or dual band display modes.
Explains "MHz" tuning, tuning step selection, and band selection.
General| Brand | Icom |
|---|---|
| Model | ID-5100A |
| Category | Transceiver |
| Language | English |
To Next Page
