Icom ID-5100A User Manual (English)

Other manuals for Icom ID-5100A

Operating Guide2 pages

Full Manual352 pages

Service Manual59 pages

Brochure & Specs4 pages

Questions and Answers:

B
Beth WalkerAug 22, 2025
What to do if Icom ID-5100A doesn't return a signal from the repeater?
- M
  Michelle ColeAug 22, 2025
  If, after transmitting, you receive no signal from the repeater, several factors could be at play. First, verify that the repeater setting is correct by selecting the appropriate repeater. If that's not the issue, your transmission might not be reaching the repeater; in this case, correct the repeater frequency, frequency offset, or duplex setting. If problems persist, try again when you are closer to the repeater or attempt to access another repeater.
A
Adam HebertAug 25, 2025
Why does my Icom Transceiver reply 'RX' or 'RPT?' and the access repeater's call sign after I transmit?
- M
  Maria CochranAug 25, 2025
  If your Icom Transceiver replies with ‘RX’ or ‘RPT?’ followed by the access repeater’s call sign after you transmit, it could be due to issues with your call sign. Ensure that your call sign is correctly set in your transceiver. Also, verify that your call sign is registered on a trust server through a D-STAR repeater, or confirm its registration.
J
John AriasAug 25, 2025
What to do if Icom ID-5100A replies 'RPT?' and call sign of the destination repeater after transmitting?
- J
  Judy RamirezAug 26, 2025
  If, after transmitting, the repeater replies 'RPT?' and the call sign of the destination repeater, it means the repeater cannot connect to the destination repeater. Check the repeater setting, or the repeater might be busy. If the repeater is busy, wait for a while, and then try again.
A
Antonio ChambersAug 27, 2025
What to do if Icom ID-5100A replies 'RPT?' and its call sign after I transmit?
- C
  ccervantesAug 27, 2025
  If, after you transmit, the access repeater replies ‘RPT?’ and its call sign, the call sign of the destination repeater is wrong. Correctly set the destination repeater call sign.
J
Jasmine LaneAug 27, 2025
How to fix a simplex operation that cannot be made in the DR screen of Icom ID-5100A Transceiver?
- K
  Kathryn KruegerAug 27, 2025
  If a simplex operation cannot be made in the DR screen on your Icom Transceiver, it means a repeater frequency is programmed. Set a simplex frequency.
Q
qjoyceAug 28, 2025
What to do if Icom ID-5100A replies 'UR?' and its call sign after I transmit?
- L
  lowerycherylAug 28, 2025
  If, after transmitting, the repeater replies ‘UR?’ and its call sign, wait for a while, and try it again.
F
Frank BanksAug 29, 2025
Why doesn't the DR screen appear even when holding down [DR] on Icom ID-5100A Transceiver?
- L
  Lisa HolmesAug 30, 2025
  If the DR screen does not appear even when holding down the [DR] button on your Icom Transceiver, it could be due to a missing repeater list. Reload the repeater list using the SD card or enter the Repeater list data directly into the transceiver.
J
Jeremy MurphyAug 31, 2025
How to fix a Local area call that can be made, but the Gateway call or destination station call cannot be made on Icom ID-5100A Transceiver?
- D
  David BurnsAug 31, 2025
  If a Local area call can be made, but the Gateway call or destination station call cannot be made on your Icom Transceiver, your call sign (MY) has not been registered on a D-STAR repeater. Register your call sign (MY) on a D-STAR repeater, or confirm the registration of the call sign.
K
katelyn78Sep 1, 2025
What does 'L' appearing on the LCD of Icom Transceiver mean?
- D
  Danielle HendricksSep 1, 2025
  If “L” appears on the LCD of your Icom Transceiver, while receiving data through the Internet, some packets may be lost due to a network error. Wait a while, and try it again. When the transceiver receives corrupted data, and misidentifies it is as packet loss, “L” appears, even if it is a Local area call.
S
Stacey CarrSep 2, 2025
How to solve the issue when the received call sign does not set to the destination call sign to make a call back on Icom ID-5100A?
- S
  Steve ContrerasSep 2, 2025
  If, even when holding down [RX>CS], the received call sign does not set to the destination call sign to make a call back on your Icom Transceiver, the transceiver did not correctly receive the call sign data. Try it again after the transceiver has correctly received the call sign.