How do I fix the frequency setting on my Icom Transceiver?
If you cannot set the frequency on your Icom Transceiver, it might be because the Lock function is activated. Hold down [LOCK] for 1 second to turn OFF the Lock function. Alternatively, the VFO mode may not be selected; push [V/M] to select the VFO mode.
Why is the frequency displayed incorrectly on my Icom ID-4100A Transceiver?
If the displayed frequency on your Icom Transceiver is erroneous, it could be due to a CPU malfunction. Try resetting the transceiver. It may also be caused by external factors. Disconnect and then reconnect the transceiver to the DC power supply.
Why is there no sound coming from my Icom Transceiver speaker?
If no sound is coming from your Icom Transceiver speaker, there could be several reasons. First, the audio volume may be too low; try rotating the [VOL] knob clockwise to increase the listening level. Also, the squelch might be tightly closed; adjust [SQL] to properly open it. If you're in FM mode, the tone squelch could be on, so turn it off. Ensure that the external speaker is correctly connected. Finally, the audio might be muted; hold down [MUTE] to release the mute function.
How to fix an Icom ID-4100A Transceiver that does not turn on?
If your Icom Transceiver does not turn on, there are a few potential causes. Ensure the power cable is correctly connected. If it still doesn't turn on, a fuse might be blown; correct the cause and replace the fuse with an equivalent one located in the DC power cable. Finally, check that the power source voltage is correct and apply the specified 13.8 V DC.
Why is the sensitivity too low on my Icom Transceiver?
If the sensitivity on your Icom Transceiver is too low, and only strong signals are audible, it could be due to a few reasons. Check if the antenna is defective or if the coaxial cable connector is shorted or cut; correct the cause and reconnect it properly to the antenna connector. Another possibility is that the Attenuator function is turned ON; turn it OFF. Also, verify that the squelch is not set too tight; adjust the [SQL] to lower the squelch level.
What to do if my Icom ID-4100A Transceiver won't transmit or has low power?
If your Icom Transceiver won't transmit or the transmit power level is low, first check if the Duplex function is ON with different transmit and receive frequencies, and turn it OFF. Then, verify that the transmit power level is set to HIGH, not LOW or MID. Also, ensure that the PTT Lock and the Busy Lockout functions are turned OFF.
Why won't my Icom ID-4100A Transceiver start a Memory Scan?
If a Memory Scan does not start on your Icom Transceiver, ensure that the Memory mode is selected by pushing [V/M]. Also, make sure that two or more memory channels have been programmed, as the scan requires multiple programmed channels to function.
What prevents my Icom ID-4100A Transceiver from starting a Program Scan?
If a Program Scan does not start on your Icom Transceiver, first check that the VFO mode is selected by pushing [V/M]. Also, verify that different frequencies are entered into the scan edges; the scan will not start if the same frequencies are entered.
Why does my Icom Transceiver transmission automatically cut off?
If the transmission is automatically cut off on your Icom Transceiver, it is likely that the Time-out timer function is activated. Turn OFF the Time-out timer function.
General| Output Power | 50W (VHF), 35W (UHF) |
|---|---|
| Voltage Range | 13.8V DC ±15% |
| Antenna Connector | SO-239 |
| Display | LCD |
| GPS | Built-in |
| D-STAR | Yes |
| Frequency Range (TX/RX) | 144-148 MHz / 430-450 MHz |
| Operating Modes | FM, D-STAR |
| Weight | 1.1 kg |
| Operating Temperature | -10°C to +60°C |
| Memory Channels | 1000 |
To Next Page
