Icom ID-4100A

10
OTHER FUNCTIONS
10-21
Cmd.
Sub
cmd.
Data Description
22 00 see p. 10-26 Send/read DV TX data (Up to 30 byte)
01 00 00 Send/read Auto DV RX data output
OFF
01 Send/read Auto DV RX data output ON
01 see p. 10-26 Send/read DV RX data (Up to 30 byte)
02 00, 01 Send/read DV data TX setting
(00=PTT, 01=Auto)
03 00, 01
Send/read DV fast data setting
(00=OFF, 01=ON)
04 00, 01
Send/read GPS Data Speed setting
(00=Slow, 01=Fast)
05 00~10
Send/read TX Delay (PTT) setting
(00=OFF, 01=1 sec. ~ 10=10 sec.)
23 00 see p. 10-26 Read the position
01 00 Send/read the GPS receiver OFF
01 Send/read the internal GPS ON
02 Send/read the external GPS ON
03
Send/read the manually entered
position
02 see p. 10-26 Send/read manually entered position
24 00 00 00 Send/read TX output power setting
OFF
01 Send/read TX output power setting ON
01 00 TX output power setting OFF for
transceive
01 TX output power setting ON for
transceive
Remote jack (CI-V) information (Continued)
*
1
Below 100 Hz is omitted.
*
2
When sending the power ON command (18 01), the
command “FE” must be sent before the basic format.
• 19200bps: 25
• 9600bps: 13
• 4800bps: 7
Example: When sending with 4800 bps
q w e r t
u
F
F E
×7
A9EFE E 10810 DF
q Preamble code (xed)
w Transceiver’s default address
e Controller’s default address
r Command number
t Sub command number
u End of message code (xed)
*
3
Output setting is automatically turned OFF after turning
OFF the transceiver, then turn it ON again.
Receive frequency setting
Command: 00, 03, 05
q
0X X X X
w e
X
r t
XX X0
10 Hz digit: 0, 3, 5, 6 (according to the 100 Hz digit)
1 Hz digit: 0 (Fixed) 1 kHz digit
:
0, 1, 2, 3, 5, 6, 7, 8
100 Hz digit: 0, 2, 3, 5, 6, 7 100 kHz digit: 0 ~ 9 10 kHz digit: 0 ~ 9 10 MHz digit: 0 ~ 9 1 MHz digit: 0 ~ 9 1000 MHz digit: 0 (Fixed) 100 MHz digit: 1, 2, 3, 4, 5
100 Hz digit 10 Hz digit
0 0
2 5
3 3
5 0
6 6
7 5
Operating mode
Command: 01, 04, 06
q
XX X X
w
Operating
mode
q Mode w Filter setting
AM 02 01
AM-N 02 02
FM 05 01
FM-N 05 02
DV 17 01
Duplex Frequency offset setting
Command: 0C, 0D
q ew
X X
X X X X
100 Hz digit
100 kHz digit
10 kHz digit
10 MHz digit
1 kHz digit
1 MHz digit
RF power level setting
Command: 14 0A
LOW MID HIGH
0 ~ 84 85 ~ 170 171 ~ 255
External microphone gain setting
Command: 14 0B
1 2 3 4
0000 ~ 0063 0064 ~ 0127 0128 ~ 0191 0192 ~ 0255
Previous view