EasyManuals Logo

Icom M700PROE Servise Manual

Icom M700PROE
52 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #18 background imageLoading...
Page #18 background image
4 - 6
TRANSMITTER ADJUSTMENTS (continued)
TRANSMIT
GAIN
OUTPUT
POWER
CARRIER
SUPPRESSION
TUNE
POWER
POWER
METER
MIC
LIMITTER
MIC GAIN
ADJUSTMENT
ADJUSTMENT ADJUSTMENT CONDITION
MEASUREMENT
VALUE
POINT
UNIT LOCATION UNIT ADJUST
1
2
1
2
3
1
1
1
2
1
1
• Display frequency : 12.2300 MHz
• mode : A1A
• Transmitting
• Display frequency : 16.3650 MHz
• Transmitting
• Display frequency : 12.2300 MHz
• Mode : H3E
Apply no audio signal to the
[MICROPHONE] connector.
• Transmitting
• Mode : R3E
• Transmitting
• Mode : A1A
• Transmitting
• Display frequency : 12.2300 MHz
• Mode : J3E
Apply no audio signal to the
[MICROPHONE] connector.
• Transmitting
• Display frequency : 12.2300 MHz
Ground the lead of L108 (KEY
line) on the MAIN unit with a wire.
• Transmitting
While pushing the [SQL] and [ENT]
switches, turn power ON.
• Display frequency : 12.2300 MHz
• Mode : J3E
Connect an audio generator to the
[MICROPHONE] connector and
set as:
Frequency : 1.5 kHz
Level : 100 mV
• Set the transmit power:
[PO-1] (20 W
PEP)
• Transmitting
• Display frequency : 12.2300 MHz
• Mode : J3E
Disconnect BFO plug (J5) on the
MAIN unit.
Connect an audio generator to the
[MICROPHONE] connector and
set as:
Frequency : 1.5 kHz
Level : 150 mV
• Transmitting
• Display frequency : 12.2300 MHz
• Mode : J3E
Connect an audio generator to the
[MICROPHONE] connector and
set as:
Frequency : 1.5 kHz
Level : 10 mV
• Transmitting
140 W
0.5 V
45 W
2.0 W
140 W
Minimum carrier level
(Less than –40 dB)
10 W
17 W
Push the [DIMMER]
switch.
70 mV
PEP
100 W
Rear
Panel
MAIN
Rear
Panel
Rear
Panel
Rear
Panel
Rear
Panel
MAIN
Rear
Panel
Connect an RF
power meter to the
[ANT] connector.
Connect a digital
multimeter to R159.
Connect an RF
power meter to the
[ANT] connector.
Connect a spectrum
analyzer or RF
voltmeter to the [ANT]
connector via an
attenuator.
Connect an RF
power meter to the
[ANT] connector.
Connect an RF
power meter to the
[ANT] connector.
Connect an
oscilloscope to R243.
Connect an RF
power meter to the
[ANT] connector.
MAIN
MAIN
MAIN
MAIN
Audio
generator
Font
Panel
LOGIC
LOGIC
R184
R26
R211
R212
R184
Adjust
alternately
R238,
R239
R205
Output
level
[DIMMER]
R2070
R2066

Other manuals for Icom M700PROE

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Icom M700PROE and is the answer not in the manual?

Icom M700PROE Specifications

General IconGeneral
BrandIcom
ModelM700PROE
CategoryTelephone
LanguageEnglish

Related product manuals