ICP N9MSB0401410B User Manual

Figure 2 1Dimensions
s 15/1
[17s.1]
2 _1o
_ [26,41
[1/0,11
1268.8]
NOTES:
1. Doors may vary by model.
2. Minimum return-air openings at furnace, based on metal duct. If flex duct is used,
see flex duct manufacturer's recommendations for equivalent diameters.
a. For 800 CFM-16-in. (406 mm) round or 14 112 x 12-in. (368 x 305 mm) rectangle.
b. For 1200 CFM-20-in. (508 mm) round or 14 1/2 x 19 1/2-in. (368 x 495 mm) rectangle.
c. For 1600 CFM-22-in. (559 mm) round or 14 112x 22 1/16-in. (368 x 560mm) rectangle.
d. Return air above 1800 CFM at 0.5 in. w.c. ESP on 24.5" casing, requires one of the following
configurations: 2 sides, 1 side and a bottom or bottom only. See Air Delivery table in this
document for specific use to allow for sufficient airflow to the furnace.
3. Vent and Combustion air pipes through blower compartment must
use accessory Went Kit - Through the Cabinet". See accessory list for
current part number.
NOTE: ALL DIMENSIONS IN INCH [MM]
[76.21 _\
AIR INTAKE
6 1116
[154.01
1 5/16
(_.31
1749_1
283/4
[730,51
• 2611/16_
(_.11
1557,4]
[s26.e]
ls,_z.7]
i_R FLOW
• ],
GAS CONN
¢7/S
--_OR ZONTAL
_[ J J-'- CONDENSATE
[101,61 LOCATION
_7/S
J_ [22,2_ POWER CONN
_-- _ 7/8 SIDE INleT
/
_¢7/8
RMOSTAT ENTRY
BOTTOM iNLET
215/8_
IS4_.S]
263/8 _
[51_.01
26 5/16
[_.e]
SD5060-4 Rev F
N9MSB
FURNACESIZE
B
OUTLET WIDTH
DA
CABINET
WIDTH
14-3/16 (361)
14-3/16 (361)
17-1/2 (445)
17-1/2 (445)
21 (533)
21 (533)
21 (533)
24-1/2 (622)
A
CABINET
WIDTH
14-3/16 (361)
14-3/16 (361)
17-1/2 (445)
17-1/2 (445)
21 (533)
21 (533)
21 (533)
24-1/2 (622)
24-1/2 (622)
AIR INTAKE
SHIP WT.
LB (KG)
0401410 12-1/2 (319) 7-1/8 (181) 123 (55)
0601410 12-1/2 (319) 7-1/8 (181) 127 (57)
0601714 15-7/8 (403) 8-3/4 (222) 144 (65)
0801716 15-7/8 (403) 8-3/4 (222) 154 (69)
0802120 19-3/8 (492) 10-1/2 (267) 162 (73)
1002114 19-3/8 (492) 10-1/2 (267) 169 (76)
1002120 19-3/8 (492) 10-1/2 (267) 169 (76)
1202420 22-7/8 (581) 12-1/4 (311 ) 186 (84)
B D
C
BOTTOM
INLET WIDTH
12-9/16 (322)
12-9/16 (322)
16 (406)
16 (406)
19-1/2 (495)
19-1/2 (495)
19-1/2 (495)
23 (584)
C
BOTTOM
INLET WIDTH
12-9/16 (322)
12-9/16 (322)
16 (406)
16 (406)
19-1/2 (495)
19-1/2 (495)
19-1/2 (495)
23 (584)
23 (584)
OUTLET WIDTH AIR INTAKE
N9MSE
FURNACESIZE
SHIP WT.
LB (KG)
0401410 12-1/2 (319) 7-1/8 (181) 123 (55)
0601410 12-1/2 (319) 7-1/8 (181) 127 (57)
0601714 15-7/8 (403) 8-3/4 (222) 144 (65)
0801716 15-7/8 (403) 8-3/4 (222) 154 (69)
0802120 19-3/8 (492) 10-1/2 (267) 162 (73)
1002114 19-3/8 (492) 10-1/2 (267) 169 (76)
1002120 19-3/8 (492) 10-1/2 (267) 169 (76)
1202420 22-7/8 (581) 12-1/4 (311 ) 186 (84)
1402420 22-7/8 (581) 12-1/4 (311 ) 190 (86)
Specifications subject to change without notice. 440 01 4101 03

ICP N9MSB0401410B Specifications

General

Brand	ICP
Model	N9MSB0401410B
Category	Furnace
Language	English