What to do if my IDEAL LOGIC 18 has no central heating or hot water?
If your IDEAL Boiler isn't providing central heating or hot water, first, make sure the mains switch (fused spur) is turned on and the mode control knob is in the ON position. Also, check the time settings on the timer and adjust them if needed. If a '0' is displayed, contact a Gas Safe Registered Engineer (or a Registered Gas Installer in IE).
What to do if there is no hot water with my IDEAL Boiler?
If you are experiencing a lack of hot water with your IDEAL Boiler, make sure the programmer is in the 'ON' position and the cylinder is turned up. Also, check that the mains switch (fused) is turned on and ensure knob (B) is in the correct position. Finally, verify that the room thermostat is turned up and the programmer is in the 'ON' position.
Why is there no central heating in my IDEAL Boiler?
If your IDEAL Boiler isn't providing central heating, first check the time settings on the programmer and adjust them as needed. If '0' is displayed, it is recommended to contact a Gas Safe Registered Engineer or, in IE, a Registered Gas Installer (RGII).
How to fix no central heating or hot water in my IDEAL LOGIC 18 Boiler?
If your IDEAL Boiler isn't providing central heating or hot water, first check that the mains switch (fused spur) is turned on and the mode control knob is in the ON position. Also, verify that the timer settings are correct and adjust them as needed.
What should I do if my IDEAL Boiler resets 5 times in 15 minutes?
If your IDEAL Boiler resets 5 times within 15 minutes, turn the power off and then on again at the fused spur. If the boiler still fails to operate, further assistance is needed.
What to do if my IDEAL LOGIC 18 has an ignition lockout?
If your IDEAL Boiler is experiencing an ignition lockout, first check if other gas appliances in your home are working to ensure there's a gas supply. If other appliances aren't working or you don't have any, check that the gas supply is turned on at the meter and/or the pre-payment meter has credit. If the boiler still fails to operate after these checks, further assistance is needed.
What to do for a Fan Fault on an IDEAL LOGIC 18?
If your IDEAL Boiler indicates a Fan Fault, reset the appliance. If the boiler fails to operate, further assistance is needed.
How do I fix a Flow Thermistor issue on my IDEAL LOGIC 18 Boiler?
If your IDEAL Boiler is showing a Flow Thermistor issue, reset the appliance. If the boiler fails to operate, further assistance is needed.
What to do if my IDEAL LOGIC 18 Boiler shows an Outside Sensor Failure?
If your IDEAL Boiler indicates an Outside Sensor Failure, reset the appliance. If the boiler fails to operate, further assistance is needed.
How to resolve a False Flame Lockout on an IDEAL Boiler?
If your IDEAL Boiler experiences a False Flame Lockout, reset the appliance. If the boiler fails to operate, further assistance is needed.
Boiler installation requires a Gas Safe Registered Engineer in accordance with regulations.
Reduced bottom clearance of 5mm is allowed with an easily removable panel.
Adjusts central heating radiator temperature up to a maximum of 80°C.
Controls room temperature automatically based on outside weather conditions.
Set the mode control knob to OFF to shut down the boiler.
Repeat the procedure detailed in 'To light the boiler'.
Guidance on protecting the system from frost during cold weather.
Boiler shuts down on overheating; fault code L-1 displayed.
Occurs during flame failure; fault code L-2 displayed.
Instructions for defrosting a frozen condensate pipe using warm water.
General| Category | Boiler |
|---|---|
| Output | 18 kW |
| Dimensions (H x W x D) | 700 x 395 x 278 mm |
| Boiler Type | Combi |
| ERP Rating | A |
| CH Output (kW) | 18 kW |
| Fuel Type | Gas |
| Mounting | Wall-mounted |
To Next Page
