IDEC FL1E-H12RCA - Page 356

To Previous Page

Index

342 IDEC SmartRelay Manual

Verification 91

Voltage levels 113

Voltage supply

connecting

Circuit protection 34

WindLGC 260

Wintertime 97

Wire ferrules 32

without display

PC-IDEC SmartRelay mode

261

reading current data 327

XOR 120

Zero division error 230

Zero offset 125

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com

Main Page

Default Chapter9
- Table of Contents9
1 Getting Started with IDEC Smartrelay15
2 IDEC Smartrelay Installation and Wiring31
- Modular IDEC Smartrelay Setup34
- Maximum Setup34
- Setup with Different Voltage Classes36
- Compatibility38
- Installing/Removing IDEC Smartrelay39
- DIN Rail Mounting40
- Wall-Mounting43
- Mounting the Text Display44
- Wiring IDEC Smartrelay46
- Connecting the Power Supply47
- Connecting the Text Display Power Supply48
- Connecting IDEC Smartrelay Inputs49
- Connecting Outputs58
- Connecting the as Interface Bus63
- Putting into Operation65
- Switching on the IDEC Smartrelay/Power on65
- Operating States68
3 Programming IDEC Smartrelay71
- Connectors72
- Blocks and Block Numbers74
- From Circuit Diagram to IDEC Smartrelay Program77
- The Four Golden Rules for Operating IDEC Smartrelay80
- Overview of IDEC Smartrelay Menus82
- Writing and Starting the Circuit Program83
- Selecting Programming Mode83
- The First Circuit Program84
- Circuit Program Input86
- Assigning a Circuit Program Name91
- Password92
- Switching IDEC Smartrelay to RUN Mode98
- Second Circuit Program100
- Deleting a Block106
- Deleting Block Groups107
- Correcting Programming Errors108
- Selecting Analog Output Values for RUN/STOP Transition108
- Defining the Type of Analog Outputs109
- Deleting the Circuit Program and Password110
- Summertime/Wintertime Conversion111
- Synchronization115
- Memory Space and Circuit Program Size117
4 IDEC Smartrelay Functions123
- Constants and Connectors - Co124
- Basic Functions List - GF128
- And129
- AND with Edge Detection130
- NAND (Not AND)130
- NAND with Edge Detection131
- NOR (Not OR)133
- XOR (Exclusive OR)134
- NOT (Negation, Inverter)134
- Special Functions135
- Designation of the Inputs135
- Time Response136
- IDEC Smartrelay Manual136
- Backup of the Real-Time Clock137
- Retentivity137
- Parameter Protection138
- Calculating the Gain and Offset of Analog Values139
- Special Functions List - SF142
- On-Delay145
- Off-Delay149
- On-/Off-Delay150
- Retentive On-Delay152
- Interval Time-Delay Relay/Pulse Output153
- Edge-Triggered Interval Time-Delay Relay154
- Asynchronous Pulse Generator156
- Random Generator158
- Stairwell Light Switch160
- Dual-Function Switch162
- Seven-Day Time Switch164
- Twelve-Month Time Switch169
- Up/Down Counter175
- Operating Hours Counter178
- Frequency Trigger182
- Analog Trigger185
- Analog Differential Trigger188
- Analog Comparator191
- Analog Watchdog196
- Analog Amplifier199
- Latching Relay204
- Current Impulse Relay205
- Message Texts207
- Softkey219
- Shift Register222
- Analog Multiplexer224
- Analog Ramp Control226
- PI Controller230
- Pulse Width Modulator (PWM)236
- IDEC Smartrelay Manual236
- Analog Math239
- Analog Math Error Detection244
5 Configuring IDEC Smartrelay247
- Selecting Parameter Assignment Mode248
- Parameters249
- Selecting the Parameters250
- Modifying Parameters251
- Setting the Default Values for IDEC Smartrelay253
- Setting the Time of Day and Date (FL1E-H12RC254
- Setting the Display Contrast and Backlight Choice255
- Setting the Menu Language257
- Setting the Number of Ais in the Base Module258
- Setting the Start Screen259
6 IDEC Smartrelay Memory  and Battery Cartridge (Card)261
- Security Function (Copyprotect)264
- Inserting and Removing Memory and Battery Cartridges266
- Copying Data from IDEC Smartrelay to the Memory Cartridge268
- Copying Data from the Memory Cartridge to IDEC Smartrelay270
7 IDEC Smartrelay Software273
- Connecting IDEC Smartrelay to a PC275
8 Applications277
- Stairway or Corridor Lighting279
- Requirements for a Stairway Lighting System279
- Previous Solution279
- Lighting System with IDEC Smartrelay280
- IDEC Smartrelay Manual281
- Special Features and Expansion Options282
- Automatic Door283
- Requirements of an Automatic Door283
- Conventional Solution284
- Door Control System with IDEC Smartrelay284
- Special Features and Expansion Options287
- Extended Solution with FL1E-H12RCC287
- Air-Conditioning System290
- Requirements for an Air-Conditioning System290
- Advantages of Using IDEC Smartrelay293
- Factory Door295
- Requirements for a Gate Control System295
- Previous Solution296
- Extended IDEC Smartrelay Solution298
- Centralized Control and Monitoring of Several Factory Doors299
- Requirements for a Gate Control System300
- Luminous Rows303
- Requirements for a Lighting System303
- Previous Solution304
- Luminous Row Control System with FL1E-H12RCC305
- Service Water Pump307
- Requirements for a Control System of a Service Water Pump308
- Previous Solution308
- Service Water Pump System with FL1E-H12RCC309
- Special Features and Expansions310
Technical Data311
General Technical Data311
Technical Data: FL1E-H12RCC/FL1E-B12RCC313
Technical Data: FL1B-M08C2R2316
Technical Data: FL1E-H12SND319
Technical Data: FL1B-M08B1S2321
Technical Data: FL1E-H12RCA/FL1E-B12RCA323
Technical Data: FL1B-M08D2R2326
Technical Data: FL1E-H12RCE/ FL1E-B12RCE and FL1B-M08B2R2328
Switching Capacity and Service Life of the Relay Outputs331
Technical Data: FL1B-J2B2332
Technical Data: FL1D-K2B2, FL1D-K2BM2333
Technical Data: Text Display334
Determining the Cycle Time335
IDEC Smartrelay Without Display339
IDEC Smartrelay Menu Structure343
IDEC Smartrelay Base Module343
Text Display345
- D.2 Text Display345
Type Numbers347
Index349

IDEC FL1E-H12RCA - Page 356

Table of Contents

Related product manuals