IEC CPY 03 User Manual

FanCoils
INSTALLATION,OPERATION,&MAINTENANCEMANUAL
10
SECTIONTWO —StartUp,Cont'd.
Eachunitshouldbecheckedfor:
1. freeblowerwheeloperation
2. loosewires
3. looseormissingaccesspanelsordoors
4. cleanlterofthepropersizeandtype
Exceptasrequiredduringstart-upandbalancingoperations,
nofancoilunitsshouldbeoperatedwithoutalltheproper
ductworkattached,supplyandreturngrillesinplace,andall
accessdoorsandpanelsinplaceandsecure.Failuretodo
socouldresultindamagetotheequipmentorbuildingand
furnishings,and/orvoidallmanufacturer’swarranties.
Cooling/Heating System
Priortothewatersystemstart-upandbalancing,the
chilled/hotwatersystemsshouldbeushedtocleanout
dirtanddebriswhichmayhavecollectedinthepiping
duringconstruction.Duringthisprocedure,allunitservice
valvesmustbeintheclosedposition.Thisprevents
foreignmatterfromenteringtheunitandcloggingthe
valvesandmeteringdevices.Strainersshouldbeinstalled
inthepipingmainstopreventthismaterialfromentering
theunitsduringnormaloperation.
Duringsystemlling,airventingfromtheunitis
accomplishedbytheuseofthestandard,manualairvent
tting,ortheoptional,automaticairventttinginstalled
onthecoil.ManualairventsarebasicallySchradervalves.
Toventtheairfromthecoil,depressthevalveuntiltheair
hasventedthecoil.Whenwaterbeginstoescapethrough
thevalve,releasethevalve.Automaticairventsmaybe
unscrewedoneturncounterclockwisetospeedinitial
venting,butshouldbescrewedinforautomaticventing
afterstart-upoperations.
CAUTION! The air vent provided on the unit is
not intended to replace the main system air vents
and may not release air trapped in other parts of the
system. Inspect the entire system for potential air traps
and vent those areas as required, independently. In
addition, some systems may require repeated venting over
a period of time to properly eliminate air from the system.
Air System Balancing
Allductworkmustbecompleteandconnected.Allgrilles,
lters,andaccessdoorsandpanelsmustbeproperly
installedtoestablishactualsystemoperatingconditions
BEFOREbeginningairbalancingoperations.
Eachindividualunitandtheattachedductworkisa
uniquesystemwithitsownoperatingcharacteristics.For
thisreason,airbalancingisnormallydonebybalance
specialistswhoarefamiliarwithallproceduresrequired
toproperlyestablishairdistributionandfan-system
operatingconditions.Theseproceduresshouldnotbe
attemptedbyunqualiedpersonnel.
Exposedunitswithoutductworkdonotrequireair
balancingotherthanselectingthedesiredfanspeed.
Afterpropersystemoperationisestablished,theactual
unitairdeliveryandtheactualfanmotoramperagedraw
foreachunitshouldberecordedinaconvenientplacefor
futurereference.
Eco-telligent
®
Motor
IftheunitisequippedwithanECMblower,additional
stepsmayberequiredduringtheairbalancingprocess.
Reviewprojectsubmittalsororderacknowledgment
todeterminewhichECMcontrolschemetheunithas.
Alternatively,matchthecontrolboardtotheillustrations.
CAUTION! Both of the procedures described
below require the control box to be powered
while adjustments are made. Line voltage components
are concealed behind a secondary cover. However,
installer should still take all reasonable precautions.

IEC CPY 03 Specifications

General

Brand	IEC
Model	CPY 03
Category	Air Conditioner
Language	English