Ingersoll-Rand Man Rider LS2-150RLP-L E Series User Manual (English)

Questions and Answers:

L
laurabarkerAug 16, 2025
Why my Ingersoll-Rand Man Rider LS2-150RLP-L E will not operate?
- E
  evanmorenoAug 16, 2025
  If your Ingersoll-Rand winch is not operating, start by checking the air supply line connections and hoses to ensure sufficient air supply. If the winch is overloaded, reduce the load to stay within the rated capacity. Also, verify that the emergency stop valve is not engaged and reset it if necessary. Check hose and fitting connections for air leaks, inspect hoses for breaks, and tighten fittings or replace hoses as needed. Install or drain air system moisture traps, moisture collecting air receivers and compressor aftercoolers to prevent air lines from freezing due to water in the air supply. After that, disconnect lines at the winch inlet and purge with clean, dry air or nitrogen.
S
suzannemitchellAug 19, 2025
What to do if throttle lever moves but Ingersoll-Rand Winches does not operate?
- A
  Arthur AustinAug 19, 2025
  If the throttle or pendant lever moves but the Ingersoll-Rand winch doesn't operate, first ensure the air pressure at the winch inlet is at least 90 psig (6.3 bar/630 kPa) at the rated volume and clean the air line filter. Check the hose and fitting connections for any air leaks, inspect the hoses for breaks, and tighten the fittings or replace the hoses as necessary.
J
Joseph ThomasAug 22, 2025
Why my Ingersoll-Rand Man Rider LS2-150RLP-L E Winches does not lift load?
- K
  Kimberly ClarkAug 22, 2025
  If your Ingersoll-Rand winch does not lift the load or does not lift to its rated capacity, verify that the air supply pressure and volume at the winch inlet meets the requirements. Clean the air line filter. Check that the brake release pilot hole is not restricted and that the seals on the cylinder piston are not damaged. The brake should start to release at 50 psig (3.5 bar/350 kPa). If the winch is overloaded, reduce the load to within the rated capacity.
A
Alice KelleyAug 26, 2025
How to prevent air lines from freezing in Ingersoll-Rand Man Rider LS2-150RLP-L E?
- B
  Brianna WilliamsAug 26, 2025
  If air lines freeze in your Ingersoll-Rand winch system, install or drain air system moisture traps, moisture collecting air receivers and compressor aftercoolers. After taking corrective action, disconnect the lines at the winch inlet and purge them with clean, dry air or nitrogen.
C
Carlos KingAug 28, 2025
What to do if load continues to move when Ingersoll-Rand Winches is stopped?
- D
  Daniel HarrisAug 28, 2025
  If the load continues to move after stopping the Ingersoll-Rand winch, check the brake friction discs and automatic band drum brake wear, as the brake might be slipping. Reduce the load to within the rated capacity if the winch is overloaded. Additionally, check the pendant/throttle levers to ensure they spring return to the normal (neutral) position when released, as the winch motor controls might be sticking.
M
Mark SheaAug 31, 2025
How to troubleshoot slow running Ingersoll-Rand Man Rider LS2-150RLP-L E Winches?
- A
  Austin KellyAug 31, 2025
  To address a slow-running Ingersoll-Rand winch, check the fittings, connections, and hoses for the correct size and length, and replace any parts that may be restricting airflow. Inspect the air line filter. Verify that the air supply pressure and volume at the winch inlet meets the requirements. Clean the air line filter.
R
Richard RamirezSep 3, 2025
What causes automatic disc brake to fail to release on Ingersoll-Rand Man Rider LS2-150RLP-L E?
- D
  Diana WilliamsSep 3, 2025
  If the automatic disc brake on your Ingersoll-Rand winch fails to release, ensure the air pressure at the inlet to the disc brake is at least 60 psig (3.4 bar/340 kPa). Inspect the brake breather for leaking piston seals; if air escapes when attempting to release the brake, replace the brake seals. Check for proper operation of the winch controls if there's no release pressure at the brake port. If the brake piston is sticking, apply 60 psig (3.4 bar/340 kPa) to the brake release port and check for brake disc movement through the brake breather hole.
K
Kara KimSep 6, 2025
Why automatic band brake cylinder will not release on Ingersoll-Rand Man Rider LS2-150RLP-L E Winches?
- T
  taylormckinneySep 6, 2025
  If the automatic band brake cylinder on your Ingersoll-Rand winch will not release, adjust the band brake to maintain the correct cylinder stroke. If air is escaping from the cylinder breather when you try to release the brake, it indicates leaking cylinder seals, so replace or repair the cylinder. Clean or replace the filter if the air supply filter is dirty.
M
Mark PetersonSep 9, 2025
What to do if Ingersoll-Rand Man Rider LS2-150RLP-L E hauls-in but does not payout?
- D
  daughertybryanSep 9, 2025
  If your Ingersoll-Rand winch hauls in but does not payout, raise the load and check the limit switch settings, as the lower limit switch may be activated. Also, determine the cause of the slack line and rectify the problem, as the slack line detector may be activated.
D
Denise DaviesSep 12, 2025
How to fix oil leak from motor end of Ingersoll-Rand Man Rider LS2-150RLP-L E?
- L
  Laura BradySep 12, 2025
  To resolve an oil leak from the motor end of your Ingersoll-Rand winch, disassemble the winch and inspect the reduction assembly seals, as the reduction assembly may be leaking.