What causes excessive coolant consumption in Ingersoll-Rand Air Compressor?
Excessive coolant consumption in your Ingersoll-Rand Air Compressor can be due to: * A coolant system leak. Repair or replace the leaking components. * See also ‘discharge air is contaminated with coolant’.
How to troubleshoot Ingersoll-Rand Air Compressor that will not start?
If your Ingersoll-Rand Air Compressor will not start, it could be due to several reasons: * There may be no power supply. Ensure the power is switched on. If it is, contact a qualified electrician. * There may be a controller failure. Check the supply to the controller and replace it if necessary. * There may be a starter failure. Isolate the supply, lock it off, tag it, and replace the failed component. Alternatively, contact your local Ingersoll Rand representative.
Why is pressure too high in Ingersoll-Rand Air Compressor because speed is not reducing?
If the pressure produced by your Ingersoll-Rand Air Compressor is too high because the speed isn't reducing as demand decreases: * The controller settings may be incorrect. Check and modify the settings. * The pressure transducer may be faulty, incorrectly calibrated, or not receiving a pressure signal. Recalibrate or replace it.
What to do if discharge air is contaminated with coolant in Ingersoll-Rand Air Compressor?
If the discharge air from your Ingersoll-Rand Air Compressor is contaminated with coolant: * Check if the scavenge pipe is blocked or broken, or if the o-ring is not sealing. Clean or replace as necessary. * Inspect the separator element for punctures, incorrect installation, the need for replacement, or incorrect sealing. Replace if needed. * If incorrect coolant has been added, drain the system, check for damage, clean, and refill with the correct coolant. * If the system has been overfilled with coolant, check for damage and drain the excess.
What causes high airend discharge temperature in Ingersoll-Rand Air Compressor?
High airend discharge temperature in your Ingersoll-Rand Air Compressor can be caused by: * Compressor operating above rated pressure: Check and modify settings. Review system requirements. * Low coolant level: Check for leaks and top up coolant. See also information about discharge air being contaminated with coolant. * High ambient temperature: Review installation and system parameters. * Insufficient cooling air: Check ducting and cooling air path. * Dirty, blocked coolant cooler (cooling air side): Clean or replace.
What causes Ingersoll-Rand Air Compressor discharge air to be too hot?
If the discharge air from your Ingersoll-Rand Air Compressor is too hot, it could be due to: * High ambient temperature: Review the installation and system parameters. * Insufficient cooling air: Check the ducting and cooling air path, and verify the direction of blower rotation. * Dirty, blocked aftercooler (cooling air side): Clean or replace it.
Why does my Ingersoll-Rand Air Compressor package draw too much current?
If your Ingersoll-Rand Air Compressor package is drawing too much current, consider these potential causes: * The compressor may be operating above its rated pressure. Check and adjust the settings accordingly. * A separator filter element might be dirty or blocked. Replace it.
Why is my Ingersoll-Rand Air Compressor package producing excessive noise?
Excessive noise from your Ingersoll-Rand Air Compressor package can be due to several reasons: * Ensure all panels and doors are properly closed. * Check for air leaks from internal pipework or components; repair or replace as necessary. * Inspect the blower or blower motor bearings for wear; repair or replace if needed. * Remove any loose debris impacting the blower during rotation and repair any damage. * Check if the blowdown valve is stuck open; repair or replace it. * Verify that the pressure relief valve is seating correctly; repair or replace it if not. * Look for vibration due to motor, airend, or blower imbalance; repair or replace the affected components.
Why is the discharge air from my Ingersoll-Rand Air Compressor too hot?
If the discharge air from your Ingersoll-Rand Air Compressor is too hot, consider these potential causes: * High ambient temperature. Review the installation and system parameters. * Insufficient cooling air. Check the ducting and cooling air path, and verify the direction of blower rotation. * Dirty or blocked aftercooler (cooling air side). Clean or replace the aftercooler.
Why does my Ingersoll-Rand R90 Air Compressor stop and not restart?
If your Ingersoll-Rand Air Compressor stops and will not restart, it could be due to: * A tripped drive controller. See Tables 4 and 5. * The controller has tripped the compressor. See Tables 4 and 5. * The maximum number of starts per hour has been exceeded.
General| Brand | Ingersoll-Rand |
|---|---|
| Model | R90 |
| Category | Air Compressor |
| Language | English |
To Next Page
