Inovance MD380 Series

Description of Function Codes
MD380 User Manual
- 216 -
Function Code Parameter Name Setting Range Default
Fb-01 :REEOHDPSOLWXGH 0.0%–100.0% 0.0%
Fb-02 :REEOHVWHS 0.0%–50.0% 0.0%
This parameter is used to determine the wobble amplitude and wobble step. The wobble
running frequency is limited by the frequency upper limit and frequency lower limit.
,IUHODWLYHWRWKHFHQWUDOIUHTXHQF\)E $:DFWXDOZREEOHDPSOLWXGH )
)UHTXHQF\VRXUFHVHOHFWLRQ[)E,IUHODWLYHWRWKHPD[LPXPIUHTXHQF\)E $:
DFWXDOZREEOHDPSOLWXGH )0D[LPXPIUHTXHQF\[)E
:REEOHVWHSIUHTXHQF\ :REEOHDPSOLWXGH$:[)E:REEOHVWHS
 ,IUHODWLYHWRWKHFHQWUDOIUHTXHQF\)E WKHZREEOHVWHSIUHTXHQF\LVDYDULDEOH
value.
 ,IUHODWLYHWRWKHPD[LPXPIUHTXHQF\)E WKHZREEOHVWHSIUHTXHQF\LVD¿[HG
value.
Function Code Parameter Name Setting Range Default
FB-03 :REEOHF\FOH 0.0–3000.0s 10.0s
FB-04 7ULDQJXODUZDYHULVLQJWLPHFRHI¿FLHQW 0.0%–100.0% 50.0%
)EVSHFL¿HVWKHWLPHRIDFRPSOHWHZREEOHF\FOH
)EVSHFL¿HVWKHWLPHSHUFHQWDJHRIWULDQJXODUZDYHULVLQJWLPHWR)E:REEOHF\FOH
 7ULDQJXODUZDYHULVLQJWLPH )E:REEOHF\FOH [ )% 7ULDQJXODUZDYHULVLQJ
WLPHFRHI¿FLHQWXQLWV
 7ULDQJXODUZDYHIDOOLQJWLPH )E:REEOHF\FOH[±)E7ULDQJXODUZDYHULVLQJ
WLPHFRHI¿FLHQWXQLWV
Function Code Parameter Name Setting Range Default
Fb-05 Set length 0–65535 m 1000 m
Fb-06 Actual length 0–65535 m 0 m
Fb-07 Number of pulses per meter
0.1–6553.5
100.0
7KHSUHFHGLQJSDUDPHWHUVDUHXVHGIRU¿[HGOHQJWKFRQWURO
The length information is collected by DI terminals. Fb-06 (Actual length) is calculated by
dividing the number of pulses collected by the DI terminal by Fb-07 (Number of pulses each
meter).
:KHQWKHDFWXDOOHQJWK)EH[FHHGVWKHVHWOHQJWKLQ)EWKH'2WHUPLQDODOORFDWHG
ZLWKIXQFWLRQ/HQJWKUHDFKHGEHFRPHV21
During the fixed length control, the length reset operation can be performed via the DI
terminal allocated with function 28. For details, see the descriptions of F4-00 to F4-09.
Allocate corresponding DI terminal with function 27 (Length count input) in applications. If
the pulse frequency is high, DI5 must be used.
efesotomasyon.com