Inovance MD380 Series

Operation, Display and Application Examples MD380 User Manual
- 70 -
4.8.10 Setting the Fixed Length Control Mode
7KH0'KDVWKH¿[HGOHQJWKFRQWUROIXQFWLRQ7KH OHQJWKSXOVHVDUHVDPSOHGE\
the DI allocated with function 27 (Length count input). The "Actual length" (Fb-06) is
obtained by dividing the number of pulses sampled by the value of Fb-07 (Number of
SXOVHVSHUPHWHU:KHQWKHDFWXDOOHQJWK LQ)EH[FHHGVWKHVHWOHQJWKLQ)E
WKH'2WHUPLQDODOORFDWHGZLWKIXQFWLRQ/HQJWKUHDFKHGEHFRPHV21
'XULQJWKH¿[HGOHQJWKFRQWUROWKHOHQJWKUHVHWRSHUDWLRQFDQEHSHUIRUPHGYLDWKH',
WHUPLQDODOORFDWHGZLWKIXQFWLRQ/HQJWKUHVHWDVVKRZQLQWKHIROORZLQJ¿JXUH
.
)LJXUH)XQFWLRQFRGHVHWWLQJIRU¿[HGOHQJWKFRQWURO
F4-04 27
(Length pulses
input)
DI5
F4-00 to F4-09
28
(Length reset)
Fb-07
(Number of
pulses per
meter)
Length pulses
Length reset
Fb-06
(Actual length)
Fb-05
(Set length)

F5-00 to F5-05 10
(Length reached)
ResetClear to 0
÷
After the length is reached,
WKH'2EHFRPHV1.
Length reset input
Length reached output
Length pulses input
1 2 3 10 11 12
1 2
Fb-06 0
Fb-06 11
Fb-05 11
80-13 (Length value)
80-13 0
Note
 ,QWKH¿[HGOHQJWKFRQWUROPRGHWKHGLUHFWLRQFDQQRWEHLGHQWL¿HGDQGRQO\WKHOHQJWKVKDOOEH
calculated based on the number of pulses.
 2QO\',FDQEHDOORFDWHGZLWKIXQFWLRQ/HQJWKFRXQWLQSXW
 $QDXWRPDWLFVWRSV\VWHPFDQEHLPSOHPHQWHGLIVLJQDORXWSXWE\WKH'2WHUPLQDOZLWKIXQFWLRQ
10 (Length reached) is fed back to the AC drive input terminal with the stop function.
)LJXUH&RPPRQDSSOLFDWLRQH[DPSOHRIWKH¿[HGOHQJWKFRQWUROIXQFWLRQ
M
DI4
MD380
DI3
DI2
&20
F4-03 26, F4-04 27
Fb-07 (Number of
pulses per meter)
581EXWWRQ
-2*EXWWRQ
Length pulses input
CME
DI1
Stop button
'21
Button for
clearing length
DI5
Length reached
output
Length
detection sensor
:LQGLQJ
motor
F0-02 1, F4-00 1
F4-01 3, F4-02 4
F4-11 2
F5-04 10
Fb-05 (Set length)
efesotomasyon.com