8
CAP. 5 – PHONE / GPS / TFT-MULTIMEDIA SYSTEM
Interphone AVANT can be connected to Bluetooth® devices, such as mobile phones, GPS and MP3
players or any other multimedia system of motorcycle brand.
5.1 Pairing
Before starting use of Interphone AVANT with these devices, it is necessary to perform pairing of the
various devices. This process need only be performed once. Subsequently Interphone AVANT will auto-
matically recognise the devices previously paired and will automatically connect.
Pairing procedure
1) Activate the Bluetooth® function on the phone/GPS/MP3/TFT (refer to the device manual for further
details).
2) With Interphone AVANT off press and hold until the LED will flash red/blue (pairing mode).
3) Start searching for new Bluetooth® devices on the mobile phone / GPS / MP3 reader / TFT.
4) After a few seconds the device will show “Interphone AVANT”. Select this option.
5) If prompted for a PIN or code, enter 0000 (four zeros).
6) The voice guide will confirm successful pairing with the message “SUCCESSFUL PAIRING, CONNECTED
TO THE PHONE” (whether the connection was started a phone, a GPS or a TFT). The device will go into
Standby mode (blue LED flashes twice every 3 seconds).
7) If the Bluetooth® device requires authorisation to access the list, provide confirmation.
To pair a second device, repeat the procedure from step 1).
5.2 Telephone use
Phone call has the highest priority than any other function. In case of incoming call use the commands
shown in the following table:
Answering a call
In case of incoming call, press the button or say the
corresponding voice command
End a call
To end a call, press the button or wait for the other
person ends the call.
Reject a call
to reject the call , wait a few seconds without answering or
say the corresponding voice command (Chapter 2.8),
With INTERPHONE AVANT in standby,following commands are available:
Voice assistant
Press the button or say the corresponding voice com-
mand (Cap. 2.8).
Redial last number
Press the button until the first beep (1.5 seconds) or say
the corresponding voice command (Cap. 2.8).
Speed dial
Press the button until the second beep (3 seconds) or
say the corresponding voice command (Cap. 2.8).
5.3 Phone call sharing
Interphone AVANT is equipped with a telephone conference function. During a phone call it is possible
to add a previously paired intercom (Chap. 4.1).
“Call sharing” is disabled by default. To enable it, refer to “Chapter 3-SETTINGS”.
Start/Stop call sharing (from unit 2)
Press the UP button until the second beep to
start/stop call sharing with unit no. 3.
Press the UP button until the second beep to
start/stop call sharing with unit no. 1.
In the case of a multi-user conference, the call will be shared with all intercoms connected downstream
of the unit that starts sharing.
5.4 Warnings and tips for using the phone
If two different mobiles are connected at the same time, the functions “Redial last number” and “Voice
call” may only be used by the first phone connected.
An Internet connection on the mobile phone may be needed to use the “Voice call”.
The “Voice call” function may not be supported by your mobile phone (refer to your device manual for
further details).
5.5 GPS
After pairing the Interphone AVANT to the GPS (Chap. 5.1) it is possible to hear the voice prompts sent
by the navigator. During a two-way intercom communication, the GPS instruction will stream in back-
ground. In the case of a multi-user conference, the GPS will interrupt the conversation for rider who
receive the prompt message but multi-user conference will remain active.
Attention: ensure the GPS is compatible with the Bluetooth® headsets. Consult the GPS user
manual for further information.
Interphone AVANT uses the Bluetooth® HFP profile to manage the connection to a GPS unit.
Navigators sold for use in cars are NOT usually equipped with Bluetooth® HFP. For that reason they
cannot transmit voice prompts to Bluetooth® headsets. Consult the GPS user manual for further infor-
mation
1 2 3
SU
GIÙ
To Next Page
Loading...
