To Next PageTo Next PageWhat to do if my Intex Swimming Pool pump doesn’t work?
If the pump isn't working, first check that the water level is correct. Then, clean the strainer screens at the pool inlet. Also, inspect the intake hose for air leaks and tighten the hose nuts, checking for any damage.
Why are there white flakes in my Intex Swimming Pool water?
If there are white flakes in the water of your Intex Swimming Pool, drain about 20 to 25% of the pool water and add fresh water to decrease the calcium hardness. Inspect the electrolytic cell for scale buildup, and clean the electrolytic cell if necessary.
How to fix Intex 128376NP Swimming Pool Pump pressure gauge that doesn't work?
If the pressure gauge on your Intex Swimming Pool Pump doesn’t work, clear any obstructions in the intake by unscrewing it from the 6-way valve.
Why is sand flowing back into my Intex Swimming Pool?
If sand is flowing back into your Intex Swimming Pool, use only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. If the sand bed is calcified, change the sand.
How to stop Intex 128376NP hose from leaking?
If the hose of your Intex Swimming Pool Pump is leaking, tighten or reinstall the hose nut. Also, ensure the o-ring or L-shape o-ring is in place and not damaged at the hose connection fitting.
What to do if Intex Swimming Pool inlet threaded air connector or air jet valve is leaking?
If the inlet threaded air connector or air jet valve of your Intex Swimming Pool is leaking, tighten or reinstall the plunger valve. Tighten the air jet valve and make sure it’s facing up. If the air jet valve internal seal is locked, turn the pump ON and run for few seconds, then turn OFF, repeat 3 times. Remove the air jet valve, flush dirt out with water and replace the valve back if the air jet valve internal seal is dirty.
How to fix Intex Swimming Pool Pump 6-way valve or cover leaking?
If the 6-way valve or cover of your Intex Swimming Pool Pump is leaking, remove the 6-way valve cover and ensure the o-ring is in place. Clean the sand tank o-ring with garden hose water if it's dirty. Tighten the flange clamp with the wrench supplied.
What to do if my Intex 128376NP Swimming Pool Pump filter doesn't clean the pool?
If your Intex Swimming Pool Pump isn't cleaning the pool effectively, ensure proper chlorine and pH levels by consulting your local swimming pool supply store. If there is no filtering media in the tank, load it with filter sand. Make sure the 6-way valve is set to the “FILTER” position. For an excessively dirty pool, operate the filter for longer periods. Clean the basket if there is dirt or sand on the pool floor.
How to fix Intex 128376NP Swimming Pool Pump filter motor that fails to start?
If the filter motor of your Intex Swimming Pool Pump fails to start, ensure the power cord is securely plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. If the RCD circuit breaker has tripped, reset it. If it trips repeatedly, there may be an electrical defect requiring an electrician. If the motor is too hot, let it cool down before restarting.
Why is my Intex Swimming Pool 6-way valve/cover leaking?
A leaking 6-way valve cover could be due to a missing sand tank o-ring, so remove the 6-way valve cover and make sure the o-ring is in place. It could also be that the sand tank o-ring is dirty, in that case clean it with garden hose water. Another cause could be that the flange clamp is not tight, so tighten it securely.
General| Brand | Intex |
|---|---|
| Model | 128376NP |
| Category | Swimming Pool Pump |
| Language | English |
