Intex 633 - User Manual

Questions and Answers

D
danielsdaisyJul 29, 2025
What to do if my Intex 633 Swimming Pool Pump filter doesn’t clean the pool?
- J
  Jill HuberJul 29, 2025
  If your Intex Swimming Pool Pump filter isn’t cleaning the pool, several factors could be at play. First, check and adjust the chlorine and pH levels, consulting with your local swimming pool supply store for guidance. A dirty filter cartridge could also be the culprit; clean or replace it as needed. Inspect the cartridge for damage, such as holes, and replace it if necessary. If the pool is excessively dirty, consider operating the filter for longer periods. Finally, ensure that the strainer screen at the pool wall inlet isn't restricting flow by cleaning it.
D
dtorresAug 3, 2025
Why doesn't my Intex 633 Swimming Pool Pump pump water or why is the flow very slow?
- R
  Robert CarneyAug 3, 2025
  If your Intex Swimming Pool Pump isn't pumping water or the flow is very slow, start by checking for obstructions in the intake or discharge hoses inside the pool wall. Next, look for air leaks on the intake line; tighten hose nuts, inspect hoses for damage, and ensure the pool water level is adequate. Clean the cartridge more often to prevent scale or buildup. If the pool is excessively dirty, clean inside the plunger valve. Also, ensure the valve handle is in the full upright position and that the nozzle and strainer connections are correctly installed, with the nozzle at the upper position of the pool inlet and the strainer at the lower position of the pool outlet.
P
powellkevinAug 7, 2025
How to fix an Intex Swimming Pool Pump that doesn't work?
- P
  pattersondominicAug 7, 2025
  If your Intex Swimming Pool Pump isn't working, first ensure the pool water level is correct. Then, clean the strainer screens at the pool inlet. Check for air leaks on the intake hose by tightening hose nuts and inspecting for damage. Also, check for any obstructions like sticks or leaves in the intake to the pump and clear them. Lastly, address potential air lock inside the cartridge chamber by turning and pulling the valve handle to the full upright position.
V
Vincent NelsonAug 11, 2025
Why won't the filter motor on my Intex 633 Swimming Pool Pump start?
- J
  Jeffery RodriguezAug 11, 2025
  If the filter motor on your Intex Swimming Pool Pump fails to start, ensure the filter cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter. Try resetting the circuit breaker; if it trips repeatedly, your electrical system may have a defect, so turn off the breaker and call an electrician. Also, the motor may be too hot; allow it to cool down.
M
Mrs. Lauren Gomez DDSAug 15, 2025
What to do if there is an air lock in my Intex 633?
- M
  Matthew HernandezAug 15, 2025
  If there's an air lock in your Intex Swimming Pool Pump, it could be due to trapped air in the pump housing and inlet hose. Open the air release valve and wait until water starts to flow out, then close the valve. Another cause could be reversed inlet and outlet hose connections. Ensure the lower position of the pool outlet connects to the filter pump water inlet, and the upper position of the pool inlet connects to the filter pump water outlet.
M
Marvin AndersonAug 19, 2025
How to fix a leaking top cover on my Intex 633 Swimming Pool Pump?
- A
  Amanda StoneAug 20, 2025
  If the top cover of your Intex Swimming Pool Pump is leaking, first remove the cover and check for the O-ring; replace it if it's missing. If the cover isn't tight, manually tighten it. Also, a dirty filter cartridge can cause leaks, so try replacing or cleaning the cartridge.
J
Jeremy KaufmanAug 25, 2025
How do I fix a hose leaking on my Intex 633?
- M
  Mr. Keith ParkerAug 25, 2025
  If a hose is leaking on your Intex Swimming Pool Pump, the hose nuts may be the issue. Try tightening or reinstalling the hose nut.