EasyManua.ls Logo

Intex SF20110 - User Manual

Intex SF20110
27 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/26/2012
127
English
Sand Filter Pump
Model SF20110
IMPORTANT
SAFETY RULES
Read, understand, and follow
all instructions carefully before
installing and using this product.
Don’t forget to try these other fine Intex products: Pools, Pool
Accessories, Inflatable Pools and In-Home Toys, Airbeds and
Boats available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex
reserves the right to change specifications and appearance,
which may result in updates to the instruction manual, without
notice.
OWNER’S MANUAL
IMPORTANT!
DO NOT RETURN PRODUCT TO STORE
To purchase parts and accessories or to obtain non-technical assistance,
Visit www.intexcorp.com
For technical assistance and missing parts call us toll-free (for U.S. and Canadian Residents):
1-800-234-6839
Monday through Friday, 8:30am to 5:00pm Pacific Time
127-***-R0-1306
For illustrative purposes only.

Table of Contents

Questions and Answers

  • D
    David HaynesAug 2, 2025
    How to troubleshoot Intex Swimming Pool Pump motor that fails to start?
    • H
      Hannah MurphyAug 2, 2025
      If your Intex swimming pool pump motor fails to start, here are a few things to check: * Make sure the motor is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. * Reset the circuit breaker if it has tripped. If it trips repeatedly, there may be an electrical system defect requiring an electrician. * If the GFCI/RCD circuit breaker has tripped, reset it. * If the motor is too hot, let it cool down before restarting.
  • W
    williamsstephanieAug 6, 2025
    What to do if Intex SF20110 Swimming Pool Pump filter doesn't clean the pool?
    • M
      Michael BensonAug 6, 2025
      If your Intex swimming pool pump filter isn't cleaning the pool effectively: * Adjust the chlorine and pH levels. * Load the tank with filter sand, following the sand loading instructions. * Ensure the 6-way valve is set to the “FILTER” position. * Operate the filter for longer periods if the pool is excessively dirty. * Clean the strainer screen at the inlet to remove any restrictions to water flow.
  • P
    Pamela WallaceAug 10, 2025
    How do I fix an inaccurate timer or a timer that can't be set on my Intex Swimming Pool Pump?
    • B
      Brandon BergAug 11, 2025
      To fix an inaccurate timer on your Intex Swimming Pool Pump: * Turn off the pump and restart it 5 minutes later. * Re-set the timer.
  • P
    Phyllis SimmonsAug 19, 2025
    How to fix a leaking 6-way valve or cover on Intex SF20110?
    • L
      Laura FuentesAug 19, 2025
      To address a leaking 6-way valve or cover on your Intex swimming pool pump: * Remove the 6-way valve cover and make sure the sand tank o-ring is in place. * Clean the sand tank o-ring with garden hose water if it's dirty. * Tighten the flange clamp with the wrench supplied.
  • J
    Jessica LoveAug 25, 2025
    How to stop an Intex Swimming Pool Pump hose from leaking?
    • M
      Mary RangelAug 25, 2025
      If you have a leaking hose on your Intex swimming pool pump: * Tighten or reinstall the hose nut securely. * Ensure the o-ring or L-shape o-ring is in place and not damaged at the hose connection fitting.
  • M
    Monica McclainAug 27, 2025
    Why is sand flowing back into my Intex Swimming Pool from the pump?
    • M
      Melanie BradleyAug 27, 2025
      If sand is flowing back into your Intex swimming pool from the pump: * Make sure you're using only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. * If the sand bed is calcified, change the sand.
  • M
    Martin BrownNov 14, 2025
    Why is my Intex SF20110 not pumping water or has very slow flow?
    • J
      James PrattNov 14, 2025
      If your Intex swimming pool pump isn't pumping water or the flow is very slow, consider the following: * Check for and clear any obstructions in the intake hose. * Tighten hose nuts, inspect hoses for damage, and ensure the pool water level is adequate to prevent air leaks. * Clean the pre-filtering basket more often if the pool is excessively dirty. * Backwash the filter if the sand media is clogged with dirt. * Ensure the nozzle is at the upper position of the pool inlet and the strainer is at the lower position of the pool outlet. * Remove about 1 inch of sand if there's crusting or caking on the filtering sand surface. * Remove any pool vacuuming devices attached to the system. * Turn off the pump, clear any debris or obstruction in the outlet, remove all air from the ...

Summary

Important Safety Rules

General Safety Rules

Comprehensive safety warnings and precautions for product use.

Parts List

Parts Reference

Visual guide and identification of all product components.

Setup Instructions

Pool Outlet - Strainer & Plunger Valve Setup

Instructions for installing pool outlet components.

Pool Inlet - Nozzle & Plunger Valve Setup

Guide for setting up the pool inlet nozzle and plunger valve.

Product Specifications

Technical details and requirements for the sand filter pump.

Pump Location and Mounting

Guidance on selecting an appropriate location and mounting the pump.

Motor Pre-filtering Assembly Setup

Steps for setting up the motor's pre-filter assembly.

Sand Tank Installation

Steps for installing the sand filter tank.

Sand Loading

Instructions for properly filling the tank with filter sand.

6-Way Valve Installation

Procedure for installing the 6-way control valve.

Sand Filter Pump Hose Connection Setup

Connecting hoses to the sand filter pump system.

Operating Instructions

6-Way Valve Positions and Function

Explains the different settings of the 6-way valve and their use.

Initial Startup and Operation

Steps for starting and operating the pump for the first time.

Operating the System Under Timer Mode or Manually

Guide on using the timer function or manual operation.

Pool Operating Time Tables

Intex Pools Operating Time Table

Recommended operating times for Intex brand pools.

Non-Intex Pools Operating Time Table

Recommended operating times for non-Intex brand pools.

Maintenance

Motor Pre-Filter Cleaning and Maintenance

Procedures for cleaning and maintaining the motor's pre-filter.

Pool Care & Chemicals

Guidance on maintaining pool water clarity and chemical balance.

Long Term Storage & Winterization

Instructions for storing the equipment during off-seasons.

Troubleshooting Guide

Common Pool Problems

Identifies and offers solutions for typical pool water issues.

General Aquatic Safety

Limited Warranty

Sand Filter Pump Warranty

Details the warranty period and terms for the pump.

Hoses, Plunger Valves & Fittings Warranty

Specifies the warranty coverage for hoses and fittings.

Intex SF20110 Specifications

General IconGeneral
ModelSF20110
CategorySwimming Pool Pump
Flow rate2000 GPH
Frequency60 Hz
Suction Size1.5 inches
Discharge Size1.5 inches
Cable Length25 feet
TypeFilter Pump

Related product manuals