How to troubleshoot Intex SF80220RC-2 motor that fails to start?
If the Intex Water Filtration Systems's motor doesn't start, ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. Also, reset the circuit breaker if it has tripped; repeated tripping may indicate an electrical system defect requiring an electrician. If the motor is too hot, allow it to cool down before restarting.
Why is the Intex SF80220RC-2 Water Filtration Systems filter not pumping water or flow is very slow?
If your Intex Water Filtration Systems isn't pumping water or the flow is very slow, check for and clear any obstructions in the intake hose. Tighten hose nuts, inspect hoses for damage, and ensure the pool water level is adequate to prevent air leaks. Clean the pre-filtering basket more often if the pool is excessively dirty. Backwash the filter if the sand media is clogged. Verify the nozzle and strainer connections are correctly positioned, with the nozzle at the upper pool inlet and the strainer at the lower pool outlet. Remove about 1' of sand if crusting or caking is present on the filtering sand surface. Detach any pool vacuuming devices and ensure the inlet threaded air connector is connected to the pool inlet's upper hole.
What to do if Intex SF80220RC-2 Water Filtration Systems doesn't clean pool?
If your Intex Water Filtration Systems isn’t cleaning the pool, adjust the chlorine and pH levels, consulting your local pool supply store for guidance. Ensure the tank is loaded with filter sand according to the 'sand loading instructions'. Set the valve to the 'FILTER' position. If the pool is excessively dirty, operate the filter for longer periods. Also, clean the strainer screen at the inlet to remove any restrictions to water flow.
Why Intex Water Filtration Systems pump doesn’t work?
If the pump of your Intex Water Filtration Systems isn’t working, first ensure the pool is filled to the correct water level. Then, clean the strainer screens at the pool inlet. Also, check for air leaks on the intake hose by tightening hose nuts and inspecting the hose for any damage. If these steps don’t resolve the issue, contact the Intex service center, as the motor may be faulty or the impeller jammed.
How to fix 6-way valve/cover leaking in Intex SF80220RC-2 Water Filtration Systems?
If the 6-way valve cover of your Intex Water Filtration Systems is leaking, remove the cover and check that the sand tank o-ring is in place. If the o-ring is dirty, clean it with garden hose water. Ensure the flange clamp is securely tightened. If the valve is damaged, contact the Intex service center.
Why is sand flowing back into the pool from my Intex SF80220RC-2?
If sand is flowing back into the pool from your Intex Water Filtration Systems, ensure you are using only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. If the sand bed is calcified, change the sand.
What to do if Intex SF80220RC-2 Water Filtration Systems inlet threaded air connector/air jet valve is leaking?
If the inlet threaded air connector or air jet valve of your Intex Water Filtration Systems is leaking, tighten or reinstall the plunger valve. Ensure the air jet valve is tight and facing up. If the internal seal is blocked, turn the pump on for a few seconds, then off; repeat this three times. If the seal is dirty, remove the air jet valve, flush out dirt with water, and replace the valve. If the valve is broken, replace it with a new one.
How to fix hose leaking in Intex Water Filtration Systems?
If the hose of your Intex Water Filtration Systems is leaking, try tightening or reinstalling the hose nut. Also, check that the hose connection fitting o-ring or L-shape o-ring is in place and undamaged.
What to do if pressure gauge doesn’t work in Intex Water Filtration Systems?
If the pressure gauge of your Intex Water Filtration Systems isn’t working, clear any obstructions in the intake by unscrewing it from the 6-way valve. If this doesn't solve the problem, contact the Intex service center, as the pressure gauge may be damaged.
Why is the timer inaccurate or can't be set on my Intex Water Filtration Systems?
If the timer on your Intex Water Filtration Systems is inaccurate or cannot be set, turn off the pump and restart it 5 minutes later. You can also try re-setting the timer. If the problem persists, contact the Intex service center, as the inner timer may be defective.
Steps for assembling the motor's pre-filter unit.
Guidance on installing the sand filter tank and related components.
General| Brand | Intex |
|---|---|
| Model | SF80220RC-2 |
| Category | Water Filtration Systems |
| Language | English |
To Next Page
