Why is the timer inaccurate or can't be set on my Intex SF70220RC-2?
If the timer on your Intex Water Filtration Systems is inaccurate or cannot be set, turn off the pump and restart it 5 minutes later. You can also try re-setting the timer. If the problem persists, contact the Intex service center, as the inner timer may be defective.
Why is the Intex Swimming Pool filter not pumping water or has very slow flow?
If your Intex Swimming Pool filter isn’t pumping water or the flow is very slow, start by clearing any obstructions in the intake hose by discharging it inside the pool wall. Check for air leaks on the intake line by tightening hose nuts and inspecting hoses for damage, also check pool water level. Clean the pre-filtering basket more often if the pool is excessively dirty. Backwash the filter if the sand media is clogged with dirt. Ensure the nozzle is at the upper position of the pool inlet and the strainer at the lower position of the pool outlet. Remove about 1” of sand if there's crusting or caking on the filtering sand surface. Remove any pool vacuuming device attached to the system line. Finally, ensure the inlet threaded air connector is connected to the pool inlet upper hole.
Why doesn't my Intex Swimming Pool filter clean the pool?
If the Intex Swimming Pool filter isn’t cleaning the pool, adjust the chlorine and pH levels. Ensure the filter tank is loaded with filter sand according to the “sand loading instructions”. Set the 6-way valve to the “FILTER” position. If the pool is excessively dirty, operate the filter for longer periods. Clean the strainer screen at the inlet if it's restricting water flow.
What to do if Intex Swimming Pool pump doesn’t work?
If the Intex Swimming Pool pump isn’t working, ensure the pool is filled to the correct water level. Clean the strainer screens at the pool inlet. Tighten hose nuts and check the hose for damage to address any air leaks on the intake hose. For a faulty motor or jammed impeller, contact the Intex service center.
How to stop sand from flowing back into the Intex Swimming Pool?
If sand is flowing back into your Intex Swimming Pool, ensure you're using No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. Also, change the sand if the sand bed is calcified.
What to do if pressure gauge doesn’t work in Intex SF70220RC-2 Water Filtration Systems?
If the pressure gauge of your Intex Water Filtration Systems isn’t working, clear any obstructions in the intake by unscrewing it from the 6-way valve. If this doesn't solve the problem, contact the Intex service center, as the pressure gauge may be damaged.
What to do if Intex SF70220RC-2 inlet threaded air connector/air jet valve is leaking?
If the inlet threaded air connector or air jet valve of your Intex Water Filtration Systems is leaking, tighten or reinstall the plunger valve. Ensure the air jet valve is tight and facing up. If the internal seal is blocked, turn the pump on for a few seconds, then off; repeat this three times. If the seal is dirty, remove the air jet valve, flush out dirt with water, and replace the valve. If the valve is broken, replace it with a new one.
How to fix hose leaking in Intex SF70220RC-2?
If the hose of your Intex Water Filtration Systems is leaking, try tightening or reinstalling the hose nut. Also, check that the hose connection fitting o-ring or L-shape o-ring is in place and undamaged.
How to troubleshoot Intex SF70220RC-2 motor that fails to start?
If the Intex Water Filtration Systems's motor doesn't start, ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. Also, reset the circuit breaker if it has tripped; repeated tripping may indicate an electrical system defect requiring an electrician. If the motor is too hot, allow it to cool down before restarting.
Why is the timer on my Intex Swimming Pool inaccurate or can't be set?
If the timer is inaccurate or can't be set on your Intex Swimming Pool, turn off the pump and restart 5 minutes later. Reset the timer. If the issue persists, contact the Intex service center.
Essential safety guidelines before installing and using the product.
Explains the different settings and water flow for the 6-way valve.
Crucial safety instructions for ladder installation and use.
Crucial safety instructions for pool installation and use.
General| Brand | Intex |
|---|---|
| Model | SF70220RC-2 |
| Type | Sand Filter Pump |
| Voltage | 110-120V |
| Power Source | Electric |
| Filter Media | Sand |
| Hose Diameter | 1.5 inch |
To Next Page
