Operation Instructions
COOL operation
- Press the "MODE" button until the "COOL" indicator
light comes on.
- Press the ADJUST buttons "+" or "- " to select your
desired room temperature. The temperature can be set
within a range of 17°C~30°C/62°F~86°F(or 88°F).
- Press the "FAN SPEED" button to choose the fan
speed.
HEAT operation(cooling only models without)
- Press the "MODE" button until the "HEAT" indicator
light comes on.
- Press the ADJUST buttons "+" or " - " to select your
desired room temperature. The temperature can be set
within a range of 17°C~30°C/62°F~86°F(or 88°F).
- Press the "FAN SPEED" button to choose the fan
speed. For some models, the fan speed can not be
adjusted under HEAT mode.
DRY operation
- Press the "MODE" button until the "DRY" indicator light
comes on.
- Under this mode, you cannot select a fan speed or
adjust the temperature. The fan motor operates at LOW
speed.
- Keep windows and doors closed for the best
dehumidifying eect.
- Do not put the duct to window.
AUTO operation
- When you set the air conditioner in AUTO mode, it
will automatically select cooling, heating(cooling only
models without), or fan only operation depending on
what temperature you have selected and the room
temperature.
- The air conditioner will control room temperature
automatically round the temperature point set by you.
- Under AUTO mode, you can not select the fan speed.
NOTE: Under AUTO mode, both the AUTO mode and
the actual operation mode indicator lights illuminate for
some models.
FAN operation
- Press the "MODE" button until the"FAN " indicator light
comes on.
- Press the "FAN SPEED" button to choose the fan
speed. The temperature can not be adjusted.
- Do not put the duct to window.
TIMER operation
- When the unit is on, press the Timer button will initiate
the Auto- o stop program, the TIMER OFF indicator
light illuminates. Press the UP or down button to select
the desired time. Press the TIMER button again within 5
seconds, the Auto- on start program is initiated.
And the TIMER ON indicator light illuminates. Press the
up or down button to select the desired Auto- on start
time.
When the unit is o, press the Timer button to initiate
the Auto- on start program, press it again within 5
seconds will initiate the Auto- o stop program.
- Press or hold the UP or DOWN button to change the
Auto time by 0.5 hour increments, up to 10 hours, then
at 1 hour increments up to 24 hours. The control will
count down the time remaining until start.
- The system will automatically revert back to display the
previous temperature setting if there is no operation in
a 5 seconds period.
- Turning the unit ON or OFF at any time or adjusting the
timer setting to 0.0 will cancel the Auto Start/Stop timer
program.
SLEEP (ECO) operation
- Press this button, the selected temperature will
increase (cooling) or decrease(heating) by 1°C/2°F(or
1°F) 30 minutes. The temperature will then increase
(cooling) or decrease (heating) by another 1°C/2°F(or
1°F) after an additional 30 minutes. This new
temperature will be maintained for the next 7 hours,
after the duration of the above time frame the unit will
return to the initial set temperature and ending the
SLEEP mode. NOTE: This feature is not available under
DRY or FAN mode.
Other features
AUTO- RESTART
In the event of power loss the unit will regain operation,
once power resumes, with the last settings.
AIR FLOW DIRECTION ADJUSTMENT
The louver can be adjusted automatically. Adjust the air
ow direction automatically:
- When the Power is ON, the louver opens fully.
- Press the SWING button on the panel or remote
controller to initiate the Auto swing feature. The louver
willl swing up and down automatically.
- Please do not adjust the louver manually.
|Operation
To Next Page
Loading...
Need help?
General
