INVENTOR V7CI-24WiFiR/U7RS-24

38
11
8°C function
LOCK function
Keep pressing Fan button for more than 2 seconds to activate/disable Silence
function.
Due to low frequency operation of compressor, it may result in insufficient cooling
and heating capacity.Pressing ON/OFF, Mode, Sleep, Turbo or Clean button while
operating will cancel silence function.
Silence function
Vane
5s
5s
Turbo
2
+
Press together Vane button and Turbo button at the
same time more than 5 seconds to activate Lock function.
All buttons will not response except pressing these two
buttons for two seconds again to disable locking.
2s
Pressing On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel this function.
Press this button 2 times during one second under HEAT Mode and setting temperature of
16°C/60°F or 20°C/68°F.
The unit will operate at high fan speed
(whilecompressor on) with temperature
automaticallyset to 8°C/46°F.
11
8°C function
LOCK function
Keep pressing Fan button for more than 2 seconds to activate/disable Silence
function.
Due to low frequency operation of compressor, it may result in insufficient cooling
and heating capacity.Pressing ON/OFF, Mode, Sleep, Turbo or Clean button while
operating will cancel silence function.
Silence function
Vane
5s
5s
Turbo
2
+
Press together Vane button and Turbo button at the
same time more than 5 seconds to activate Lock function.
All buttons will not response except pressing these two
buttons for two seconds again to disable locking.
2s
Pressing On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel this function.
Press this button 2 times during one second under HEAT Mode and setting temperature of
16°C/60°F or 20°C/68°F.
The unit will operate at high fan speed
(whilecompressor on) with temperature
automaticallyset to 8°C/46°F.
Functia Silent
Continuati sa apasati butonul FAN mai mult de 2 secunde pentru a activa /
dezactiva functia Silent (unele unitati).
Datorita functionarii cu frecventa redusa a compresorului, aceasta poate
duce la o capacitate de racire si incalzire insucienta. Apasand butonul ON
/ OFF, Mode, Sleep, Turbo sau Clean in timpul functionarii va anula functia
Silent.
Functia 8°C
Apasati acest buton de 2 ori in timpul unei secunde in modul HEAT si reglati temperatura
de 16°C / 60°F.
Unitatea va functio-
na la viteza mare a
ventila-torului (in timp
ce com-presorul este
pornit) cu temperatura
setata automat la 8
° C/
46 ° F.
Apasand On / O, Sleep, Mode, Fan si Temp. in timpul functionarii va anula aceasta functie.
Apasati simultan butonul Vane si butonul Turbo mai
mult de 5 secunde pentru a activa functia de blocare.
Toate butoanele nu vor raspunde, cu exceptia apasarii
acestor doua butoane din nou timp de doua secunde
pentru a dezactiva blocarea.
11
8°C function
LOCK function
Keep pressing Fan button for more than 2 seconds to activate/disable Silence
function.
Due to low frequency operation of compressor, it may result in insufficient cooling
and heating capacity.Pressing ON/OFF, Mode, Sleep, Turbo or Clean button while
operating will cancel silence function.
Silence function
Vane
5s
5s
Turbo
2
+
Press together Vane button and Turbo button at the
same time more than 5 seconds to activate Lock function.
All buttons will not response except pressing these two
buttons for two seconds again to disable locking.
2s
Pressing On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel this function.
Press this button 2 times during one second under HEAT Mode and setting temperature of
16°C/60°F or 20°C/68°F.
The unit will operate at high fan speed
(whilecompressor on) with temperature
automaticallyset to 8°C/46°F.
12
SET function
or
SET
SET
OK
Press the SET button to enter the function setting, then press SET button or TEMP or TEMP
button to select the desired function. The selected symbol will flash on the display area, press the
OK button to confirm.
To cancel the selected function, just perform the same procedures as above.
Sleep function( ) :
Follow me function( ):
The FOLLOW ME function enables the remote
control to measure the temperature at its
current location and send this signal to the
air conditioner every 3 minutes interval.
When using AUTO, COOL or HEAT modes,
measuring ambient temperature from the
remote control(instead of from the indoor
unit itself) will enable the air conditioner to
optimize the temperature around you and
ensure maximum comfort.
AP function( ) :
Choose AP mode to do wireless network
configuration. For some units, it doesn’t
work by pressing the SET button. To enter
the AP mode, continuously press the LED
button seven times in 10 seconds.
Press the SET button to scroll through operation functions as follows:
Active clean ( ) Sleep( ) Follow Me( ) AP mode ( ) Active clean




Active clean function( ) :
The Active Clean Technology washes away dust,
mold, and grease that may cause odors when it
adheres to the heat exchanger by automatically
freezing and then rapidly thawing the frost.
When this function is turned on, the indoor unit
display window appears “CL”, after 20 to 45
minutes, the unit will turn off automatically and
cancel CLEAN function.
The SLEEP function is used to decrease
energy use while you sleep (and don’t need
the same temperature settings to stay
comfortable). This function can only be
activated via remote control.
For the detail, see sleep operation in
“USER’S MANUAL”
Note:
The SLEEP function is not available
in FAN or DRY mode.
NOTE:
Press and hold Turbo button for seven
seconds to start/stop memory feature of
Follow Me function.
If the memory feature is stopped,“OF ”
displays for 3 seconds on the screen.
While the memory feature is activated,
press the ON/OFF button, shift the mode
or power failure will not cancel the
Follow me function.
If the memory feature is activated,“On”
displays for 3 seconds on the screen.
Functia LOCK