How to fix Inventum Dishwasher when the program does not start?
If the program on your Inventum Dishwasher doesn't start, check the following: * Ensure the mains plug is connected. * Check the fuse box for any issues. * Open the water tap to ensure there's a water supply. * Close the dishwasher door properly. * Start the appliance, making sure it is switched on. * Ensure the water inlet hose and filters are not clogged.
Why are there white stains on my inventum IVW6035A Dishwasher dishes?
White stains on dishes from your Inventum dishwasher can occur due to: * Insufficient detergent. * Low rinse aid consumption level. * High water hardness without salt usage. * Incorrect water hardness level setting. * The salt reservoir cap not being closed correctly. To address this, ensure you use enough detergent, adjust the rinse aid consumption level, fill the salt reservoir if you have hard water, adjust the salt consumption level, and make sure the salt reservoir cap is firmly closed.
What to do if my inventum IVW6035A contains water when the program is finished?
If your Inventum dishwasher still contains water after the program finishes, it could be due to: * A clogged or twisted drain hose. Make sure that the drain hose is not clogged or twisted. * Clogged filters. Clean the filters. * The program not being completely finished. Wait until the program is finished; a buzzer will sound five times, and the ready indicator will light up.
How to resolve rust stains on Inventum Dishwasher dishes?
Rust stains on dishes from your Inventum dishwasher may be due to: * Insufficient stainless steel quality of the dishes, so ensure you only clean dishwasher-safe dishes. * The level of salt consumption being set too high, so adjust the level of salt consumption. * The cap of the salt reservoir not being closed correctly, so ensure it is firmly closed. * Spilled salt during filling not being cleaned immediately, so clean any spilled salt and run a full program to prevent corrosion. * Polluted water supply, so check the water supply.
Why does my inventum IVW6035A Dishwasher appliance stop during a program?
Your Inventum dishwasher might stop mid-cycle due to: * A power failure. Ensure there is power. * A water inlet failure. Ensure there is a water inlet supply.
How to fix unusual sounds during Inventum Dishwasher program?
Unusual sounds during an Inventum dishwasher program can be caused by: * Incorrect loading of the appliance, so ensure you load it correctly. * Spray arms hitting the dishes, so ensure you load the appliance correctly.
What to do if Inventum Dishwasher detergent reservoir contains detergent residues?
If the detergent reservoir in your Inventum Dishwasher contains residues, it's likely because the reservoir was damp when filled. Make sure to fill the detergent reservoir when it is dry.
Why inventum IVW6035A dishes are not dry?
If the dishes in your Inventum Dishwasher are not drying properly, it may be because the selected program does not include a drying cycle. Choose a program that includes drying.
What does F5 error mean on inventum IVW6035A Dishwasher?
The F5 error code on your Inventum dishwasher indicates an insufficient water supply. Make sure the water tap is fully open and the water supply isn't blocked. Close the tap, remove the inlet hose, and check for clogs. Restart the appliance. If the error persists, contact Inventum-servicedienst.
What does F2 error mean on Inventum Dishwasher?
The F2 error on your Inventum dishwasher means the waste water isn't being discharged. Check the drain hose and filters for clogs. Switch the appliance off, reset the program, and if the error continues, contact Inventum-servicedienst.
General| Type | Freestanding |
|---|---|
| Energy Efficiency Class | E |
| Number of Programs | 6 |
| Noise Level | 49 dB |
| Capacity | 12 place settings |
| Color | White |
| Delay Start | Yes |
| Half Load Option | Yes |
| Child Lock | No |
To Next Page