inventum VVW4530AW User Manual (English)

Questions and Answers:

D
Dean OchoaAug 21, 2025
Why won't my inventum VVW4530AW Dishwasher program start?
- R
  Richard SmithAug 21, 2025
  There are several reasons why your Inventum Dishwasher program might not be starting: * The mains plug may not be connected: Connect the mains plug. * There may be a problem with the fuse: Check the fuse box. * There is no water supply: Open the water tap. * The door of the appliance is open: Close the door. * The appliance is switched off: Start the appliance. * The water inlet hose and filters are clogged: Ensure that the water inlet hose and the filters are not clogged.
B
burnettkellyAug 22, 2025
Why is there water left in my Inventum Dishwasher after the program finishes?
- S
  Sarah WoodsAug 22, 2025
  If your Inventum Dishwasher has water remaining after the program, it could be due to a clogged or twisted drain hose, so make sure that the drain hose is not clogged or twisted. Another possible cause is clogged filters. In this case you need to clean the filters. Also, make sure that the program has finished. A buzzer sounds five times and the ready indicator is on when a program is finished.
J
Jesse BrownAug 25, 2025
How to fix food waste left on dishes in inventum VVW4530AW?
- M
  Melissa JordanAug 25, 2025
  If you find food waste on your dishes after a wash in your Inventum Dishwasher, it's likely due to incorrect loading. Ensure that you load the appliance correctly so the spray arms can reach all the dishes.
S
scottsmithAug 26, 2025
How to get rid of white stains on dishes from inventum VVW4530AW?
- K
  Kimberly CookAug 26, 2025
  White stains on dishes from your Inventum Dishwasher can be caused by several factors: * Insufficient detergent: Ensure you fill the detergent reservoir with enough detergent. * Low rinse aid: Adjust the level of rinse aid consumption. * Hard water and no salt: Fill the salt reservoir. * Salt reservoir cap not closed: Make sure the cap is firmly closed.
R
Rhonda JonesAug 28, 2025
What to do if my inventum VVW4530AW Dishwasher appliance stops during a program?
- P
  pagetaylorAug 28, 2025
  If your Inventum Dishwasher stops mid-cycle, it could be due to a power failure. Make sure that there is power. Alternatively, there might be a water inlet failure, so ensure there is water inlet supply.
D
Dawn ZimmermanAug 29, 2025
How to fix rust stains on dishes in inventum VVW4530AW?
- J
  Jared MorrisonAug 30, 2025
  Rust stains on dishes from your Inventum Dishwasher can occur due to: * Poor stainless steel quality: Use only dishwasher-safe dishes. * High salt level in water: Adjust the level of salt consumption. * Loose salt reservoir cap: Ensure the cap is firmly closed. * Spilled salt: Clean any spilled salt immediately and run a full program to prevent corrosion. * Grounding issue: Contact an authorized electrician.
T
thompsonjenniferAug 31, 2025
How to fix dishes not drying in inventum VVW4530AW?
- D
  Deborah HuynhAug 31, 2025
  If your dishes aren't drying in your Inventum Dishwasher, it could be because the selected program doesn't include drying, so choose a program that includes drying. Alternatively, the level of rinse aid consumption may be set too low, so adjust the level of rinse aid consumption.
A
arnoldjenniferSep 2, 2025
Why does my inventum VVW4530AW Dishwasher make unusual sounds during a program?
- J
  Joyce SmithSep 2, 2025
  Unusual sounds during an Inventum Dishwasher program often mean a spray arm is hitting the dishes. Make sure that you load the appliance correctly.
C
Carol ObrienSep 3, 2025
Why does the detergent reservoir of my Inventum Dishwasher contain detergent residues?
- A
  Abigail PetersonSep 3, 2025
  Detergent residues in the detergent reservoir of your Inventum Dishwasher usually happen because the reservoir was damp when filled. Make sure that you fill the detergent reservoir when it is dry.
L
Lucas SandersSep 5, 2025
What does F5 error mean on inventum VVW4530AW Dishwasher?
- D
  Dr. Brittany GonzalezSep 6, 2025
  The F5 error code on your Inventum Dishwasher indicates insufficient water supply. Make sure that the water tap is fully open and that the water supply is not blocked. Close the water tap, remove the water inlet hose and clean the filter of the hose. Contact the Inventum-servicedienst if the fault code keeps re-occuring.