Ioline FlexJet E - Visual Reference Guide

71 pages

Save Page as PDF

To Next Page

To Previous Page

The Ioline FlexJet E Printer Front View.

A. Left End Cover

B. Right End Cover

C. Take-up Motor

D. Stand Leveling Foot

E. Feed Roll

F. Take-up Shaft

G. Feed Shaft

H. Dancer Bar

I. Stand

AA. Power Switch

BB. Serial Port

CC. USB Port

KEY

AA BB

Rear Panel Behind Right End Cover

Visual Reference Guide

Main Page

Default Chapter4
- Table of Contents4
Safety & Cautions9
Visual Reference Guide10
Chapter 1 Overview13
Getting Started13
How the Ioline Flexjet E and Studiojet Printers Work14
Chapter 2 Installation15
Printer Assembly15
- Unpacking the Printer15
- Assembling the Stand15
- Attaching the Printer to the Stand15
- Connect the Printer to the Computer: Overview15
- Cable Connections16
- Serial Configuration16
- COM Port16
- Baud Rate17
- Other Serial Port Settings17
- Software Setup Options17
Power on19
Installing Flexplot and the Control Center19
Chapter 3 Operation21
Keypad Controls21
- Start/Stop21
- Clean22
- Quality22
- Set Origin22
- Arrow Keys23
- Page Advance23
- Unroll (Flexjet E Only)23
Special Key Combinations23
- Roll up (Flexjet E Only)23
- Reset Serial Port Baud Rate23
- Restore Factory Default Settings23
The Control Center24
- Overview24
- Changing System Settings24
Control Center Menu Bar Features25
- File25
- Communications25
- Tools25
- Help25
Control Center Menu Options26
- Software Version26
- Cartridge Count26
- Get Plotter Data26
- Plotter Data (Check Box)26
- Line Width26
- Scale26
- Frame Size26
- Quality Setting27
- Measurement Units27
Consumables27
- Paper27
- Ink27
- Guidelines for Installing a Cartridge27
Printing a Marker28
- Overview28
- General Guidelines28
Loading Paper on the Studiojet29
Loading Paper on the Flexjet E Printer29
Installing the Take-Up Shaft (Flexjet E Models Only)30
Feeding Paper (Flexjet E Models Only)31
Tape Paper to the Take-Up Shaft (Flexjet E Models Only)32
Positioning the Pinchwheels32
Insert Front Dancer Bar (Flexjet E Models Only)33
Insert Read Dancer Bar (Flexjet E 2H+ Models Only)34
Set an Origin34
Sending Plot Files34
Pausing a Marker Plot34
Canceling a Marker Plot35
Removing Markers from the Take-Up Shaft (Flexjet E Models Only)35
Manually Freeing the Take-Up Shaft (Flexjet E Models Only)36
Automatically Freeing the Take-Up Shaft (Flexjet E Models Only)37
Reattach Paper to the Take-Up Shaft (Flexjet E Models Only)37
Printing to the Floor38
Chapter 4 Routine Maintenance39
Cleaning the Drive Shaft39
Cleaning the Platen and Traverse39
Cleaning the Support Blocks (Flexjet E Models Only)40
Size Calibration40
- Prepare the Printer (See the Operation Chapter)40
- Use the Control Center to Gather the Calibration Data41
- Enter the Calibration Data41
Cartridge Calibration42
- Prepare the Printer42
- Motion Adjust (Carriage Scan Alignment)43
- Frame Gap (Paper Scan Alignment)43
Cartridge Maintenance and Handling44
- Check Cartridges44
- Automatic Cleaning Procedure44
- Manual Cleaning Procedure45
Print Cartridge Storage46
- Short-Term Storage (7 Days or Less)46
- Long-Term Storage (Greater than 7 Days)46
Updating Firmware Using the Control Center46
- Summary46
- Prepare the Printer for a Firmware Update46
- Check the Current Firmware Version46
- Update the Firmware47
- Reset Calibration Values48
Chapter 5 Troubleshooting49
General Troubleshooting49
Media Tracking49
Printing Quality50
Line Quality50
Serial Communication50
Keypad Error Codes51
- Legend51
Common Issues52
Common Issues (Flexjet E Models Only)55
Chapter 6 End Notes57
Service & Support57
Getting Help57
Customer Service58
Your Comments Are Requested58
Before You Contact Support59
The FCC Wants You to Know60
Glossary61
Index65

Ioline FlexJet E - Visual Reference Guide

Table of Contents

Other manuals for Ioline FlexJet E