Stitch'n Fold
CORNER STITCHING
Lower the folding gate by pressing the toggle switch
located on the secondary table. The side stitched
sets will drop o the end of the secondary table
unfolded. The booklet stacker assembly, item 6 on
page 29, can be relocated to catch the nished sets.
With Optional Side/Corner Stitch Gate:
Corner stitching can be done with 5.5" x 8.5" or 8.5"
x 11" (also: A4 or A5) paper. In all cases, mount
one head in the far right position. (Be sure there is
a clincher, item #8 on page 20, in the far right po-
sition. If necessary, relocate the far left clincher to
the far right position.) The other head may be re-
moved or left in another position without wire. Use
thumb screw to mount gate assembly on the middle
of the stitcher head mounting bar. See page 33 for
picture of gate assembly. Connect cord from gate to
socket on left inside wall.
Adjust the left side guide for paper length. For in-
stance, if 8.5" x 11" paper is being corner stitched,
the side guide must be set for the 12" length. Align
the outer edge of the left side guide with the table
scale as follows:
11" paper 12" mark
8.5" paper 7" mark
A4 paper 13.4" mark
A5 paper 6.5" mark
An accessory guide must be mounted on the right
hand side for corner stitching. Using thumb screws
and wing nuts, attach the corner stitch guide (9" long
sheet metal part) to the two holes in the right side
guide.
See items 1, 2, and 3 on page 35.
Place two sheets between the side guides, and slide
them under the ski until they stop against the corner
stitch gate. Pull the right side guide left to the jogged
position. If there is a gap or the paper buckles,
loosen the thumb screw on the right-hand side guide
and move it in the correct direction. Use the hand
crank to adjust the position of the back jog until the
Without Optional Side/Corner Stitch Gate:
Corner stitching can be done with 5.5" x 8.5" or 8.5"
x 11" (also: A4 or A5) paper. In all cases, mount
one head in the far left position. The other head may
be removed or left in any position without wire.
Two accessory guides must be mounted on the left
hand side for corner stitching. See page 35 for
picture of accessories. First, adjust the standard left
side guide as far as possible to the left. Using thumb
screws and wing nuts, attach the corner stitch guide
(9" long sheet metal part) to the two holes in the left
side guide.
Next, lift open the top guard. Using two thumb
screws, attach the corner stitch bar (11" long bar) to
two holes in the table on the far left. The angle on
the bar should face the front and middle of the ma-
chine. Adjust the left side guide until the corner
stitch guide is aligned with the corner stitch bar.
Adjust the right side guide for paper length. For
instance, if 8.5" x 11" paper is being corner stitched,
the side guide must be set for the 11" length. Align
the outer edge of the right side guide with the table
scale as follows:
11" paper 11" mark
8.5" paper
6" mark
A4 paper 12.38" mark
A5 paper 6.54" mark
Adjust the stitching gate for paper width. For in-
stance, for 8.5" x 11" paper, the gate must be set for
the 8.5" width. First, lift open the front guard. Place
a sheet on the table between the side guides, and
slide it under the ski until it stops against the gate.
Turn the knob until the trailing edge of the paper is
just in front of the clinchers.
paper just ts between the gate and the raised jog
ngers. If the standard fold gate returns early and
causes a jam or double stitch, turn the gate timer
clockwise enough to prevent the problem.
10
To Next Page
Loading...