Name: ITT Bornemann SLH-4U
Brand: ITT
Rating: 4 (1 reviews)

To Next Page

To Previous Page

037/2020-Rev0-JP, 1, en_GB

Type SLH-4U2

03/2020 JP Rev. 1

Table of Contents3
About this Manual6
Target Groups6
Additionally Applicable Documentation6
Warning Signs and Symbols7
Technical Terms8
Safety10
Intended Use10
Improper Use10
Risk Assessment11
Safety Instructions12
Product Safety12
Obligations of the Operator13
Obligations of the Personnel14
Laws, Guidelines and Standards14
Special Hazards14
Potentially Explosive Area15
Hazardous Pumped Medium15
Concentration of Natural Radioactivity15
Structure and Function16
Labelling16
Type Plate16
Type Designation17
Structure17
Shaft Seals19
Mechanical Seal19
Auxiliary Operating Systems20
CIP/SIP Cleaning (Cleaning/Sterilisation in Place)20
Transport and Storage21
Transportation21
Unpacking and Checking the Condition of Contents21
Lifting21
Preservation23
For Storage Periods Less than 3 Months23
For Storage Periods Longer than 3 Months (Maximum 3 Years)23
Storage24
Removing Preservative24
Installation and Connection26
Preparing the Pump Assembly26
Preparing the Pump26
Fitting the Heat Insulation (Optional)26
Fitting the Coupling27
Installing the Motor on the Base Plate28
Preparing for Installation28
Checking the Ambient Conditions28
Preparing the Installation Site28
Preparing the Foundation and Base29
Positioning the Pump Unit on the Foundation29
Placing the Pump Unit on the Foundation30
Aligning the Base Plate30
Secure the Pump Assembly31
Mounting the Pump Unit Without Foundation32
Aligning the Pump Assembly32
Determining Alignment Tolerances32
Pump Alignment Tolerances33
Taking into Account Peak Height Changes35
Checking the Coupling Alignment36
Aligning the Motor37
Fitting the Coupling Guard38
Planning Pipes38
Configuring Supports and Flange Connections38
Determining Nominal Widths38
Determining Pipeline Lengths39
Optimising Cross Sectional and Direction Changes39
Avoiding Overpressure39
Including Safety and Control Equipment40
Using Hose Lines42
Connecting Pipelines42
Avoiding Contamination of the Pipes43
Installing Auxiliary Pipes43
Installing the Inlet Line43
Installing the Outlet Line43
Checking that the Pipe Connection Is Tension Free43
Electrical Connection44
Earth the Pump44
Connect the Motor44
Checking the Direction of Rotation45
Connecting the Instrumentation45
Operation46
Performing Initial Commissioning46
Determining the Pump Type46
Commissioning after Shutdown47
Removing Preservative47
Lubricate Gears47
Preparing Auxiliary Operating Systems (if Present)47
Inertisation (in Potentially Explosive Atmospheres)48
Filling and Bleeding48
Switching on49
Switching off51
Operation51
Preparing for Operation51
Switching on52
Switching off53
Cleaning/Sterilizing the Pump53
CIP Cleaning/Sterilising at CIP Temperature below 80 °C54
CIP Cleaning/Sterilising at CIP Temperature above 80 °C and Pump with Sealing System or Quench System54
CIP Cleaning/Sterilising at CIP Temperature above 80 °C and Pump Without Sealing System, Without Quench System54
Mechanically Cleaning/Sterilising55
Putting out of Operation56
Measures in Accordance with the Conveyed Medium56
Recommissioning56
Operating the Stand-By Pump57
Disposal57
Maintenance and Repairs58
Wearing Parts58
Monitoring58
Maintenance59
Clean61
Maintenance Table61
Lubrication63
Remove Pump and Send to Manufacturer64
Remove Pump64
Return Pump to the Manufacturer65
Repair Pump66
Order Spare Parts66
Lubrication Points67
Lubricant67
Transmission Oil, Temperature of the Medium to be Pumped: 10 - 300 °C67
Preservative Agents68
Cleaning Fluid69
Troubleshooting70
Appendix72
Technical Data72
Ambient Conditions72
Noise Level72
Declaration of no Objection73
Declaration in Accordance with the EC Machinery Directive74
Declaration of Conformity in Accordance with the EC Machinery Directive74
Declaration of Incorporation in Accordance with the EC Machinery Directive75

Brand	ITT
Model	Bornemann SLH-4U
Category	Water Pump
Language	English

ITT Bornemann SLH-4U User Manual

Table of Contents

Questions and Answers:

ITT Bornemann SLH-4U Specifications

Related product manuals