JABSCO 29200-0120 - User Manual

Models 29200-0120 12 Volt
29200-0240 24 Volt
ELECTRIC FLUSH PUMP
FEATURES
• Directly replaces Manual Pump Assembly
• Easy to install
• Fits all Jabsco manual toilets and
others with optional adapters
• Simple to operate
• Built-in macerator
SPECIFICATIONS
Ports: Inlet - 3/4" Hose Barb; Discharge - Attach
manual pump 11/2" discharge elbow
Motor: Permanent magnet type with ball bearings
on double ended stainless steel shaft
Pumps: Two flexible impeller pumps mounted on
opposite ends of double ended motor
Weight: 71/2 lb (3,4 kg)
Dimensions: 10-1/2" (267 mm) high, 3-3/8" (86 mm) wide,
5-7/8" (149 mm) deep, 40" (1000 mm) wire leads
APPLICATION
The Jabsco Electric Flush Pump will convert any Jabsco or
PAR manual toilet to electric operation. It is assembled at
the factory to fit the 29090-Series and 29120-Series toilets
which have been in production since 1987. The flush pump
assembly simply replaces the entire manual pump assembly
and screws directly to the toilet base. In addition to Jabsco
& PAR toilets, the flush pump will also fit the Brydon Boy,
Mansfield (Sealand) 751, Raske & Van der Meyde RM69, and
Taiwan Magnetics TMC 999 toilet models.
In order to install the Flush Pump on the following listed
toilet models, the indicated optional mounting flange must
be installed on the pump assembly.
Pump Mounting Flush Pump Mounting
Toilet Model Configuration Flange Adaptor Kit
PAR3 Hole 29060-0000
BRYDON BOY Triangle
GROCO HC
Mansfield 750 2 Hole 29125-0000
GROCO HE 3 Hole 29080-0000
GROCO HF Equilateral Triangle
Raritan Compact
Raritan PH & PH II 4 Hole 29110-0000
Sealand 752 Square Pattern
Wilcox Crittenden
Head Mate 1460 C 4 Hole 29128-0000
Wilcox Crittenden Square Pattern
Winner R4042C*
* The Wilcox Crittenden Flange Kit includes a 90° discharge elbow
and joker valve which must be used in place of the original elbow
and joker valve. The Winner toilet requires minor repositioning of
the discharge plumbing because the new discharge elbow will be
lower and about 4 inches further from the toilet bowl.
Models 29200-0120, 29200-0240
The pump may be installed on toilets which are mounted as
high as 2 feet above the vessel's waterline or on toilets below
the waterline if the total cumulative discharge head does not
exceed 6 feet. It will fit toilets with either a compact size bowl or
large household size bowl. Generally, the pump requires no
modification or additions to the existing plumbing which services
the manual pump assembly. However, if the discharge hose
rises and falls repetitively and the total of all rising segments
(when added together) exceeds 6 feet, it should be re-routed so
the total cumulative rise is less than 6 feet. If this can not be
done, the electric flush pump should not be installed.
INSTALLATION
The pump is assembled at the factory with a base mounting
flange (macerator housing) which fits the 29090-Series and
29120-Series toilets. If the pump is to be installed on a PAR
59128-Series (Brydon Boy), Mansfield (Sealand) 751, Raske
& Van Der Meyde RM69, Simpson Lawrence 444, orTaiwan
Magnetics TMC 999, it is necessary to replace the four hole
mounting flange with one of the optional mounting flanges listed
in the Application section.
To change the mounting flange, remove the four screws (on
bottom of pump assembly) which secure the mounting flange to
the waste pump body. Note the relative position of the long and
short screws.
Flood hazard. If toilet is installed below the
waterline or may be below the waterline at any
angle of heel or trim, it must be installed with
properly positioned vented loops. Failure to do
so can result in flooding which can cause loss
of property and life.
WARNING
!

Summary

Application and Compatibility

Installation Guide

Important Safety Warning for Installation

Warning about flood hazard if toilet is installed below waterline without proper vented loops.

Operation and Maintenance

Operating Instructions

Details on how to operate the flush control knob for flushing and draining the toilet bowl.

Service Instructions Overview

General safety precautions and steps for disconnecting the pump before service.

Flush Pump Disassembly

Step-by-step guide for taking apart the flush pump assembly, including impeller and switch removal.

Waste Pump Disassembly

Procedure for disassembling the waste pump body, macerator housing, chopper, and wearplate.

Reassembly Procedures

Instructions for reassembling both the waste pump and flush pump components.

Parts Identification

Exploded View Diagram

A detailed exploded view diagram illustrating all components of the electric flush pump.

Parts List and Repair Kits

A comprehensive list of all parts with their part numbers and availability of repair kits.

JABSCO 29200-0120 Specifications

General

Model Number	29200-0120
Brand	JABSCO
Voltage	12 VDC
Impeller Material	Neoprene
Inlet/Outlet Size	1/2" NPT
Self-Priming	Yes
Shaft Seal	Lip Seal
Current Draw	6 Amps