Jacuzzi city spa - (Smart Winter Mode); Water Filtering; General Information; Setting the Filtering Cycles

2626
XKeep keys “ ” or “ ” pressed down to change the value pre-
sented, from a minimum of 15 °C to a maximum of 40 °C
NOTE: press the “ ” key to increase the value or the “ ”key to
decrease it.
When the system is turned o, or there is a power outage, the last
set point is stored in memory.
Operation of the heater is shown on the display by a LED on
steady under the symbol .
XTo show the temperature of the water in the tub again, do
not touch any key for about 5 seconds.
XAs soon as the water temperature set point is reached, the
heater is shut o. It will not be turned back on until the water
temperature drops about 0.5 °C below the set point.
NOTE: in the instance where the “Silence” function is active (see
“Utility functions”), if the water falls under the “set-point” value, the
heater is not automatically turned back on. Where it is necessary to
adjust the temperature, the control panel keys must be used.
XTo ensure precise measurement of the water temperature,
the ltering pump comes on every half hour for about 30 sec-
onds (even if no ltering cycles were set), since the temperature
probe is located in the heater pipe.
NOTE: in the instance where the “Silence” function is active (see
“Utility functions”), the water temperature is taken without activat-
ing the pump.
CAUTION

Do not use the spa if the water temperature is 40 °C or more.
Maintenance of minimum temperature of water in tub and
anti-freeze protection of the pipes (“Smart Winter”).
At regular intervals, the system reads the actual temperature. If it
is below the minimum admissible value (14 °C), the heater and the
ltering pump are automatically activated until the temperature
rises above that value.
The pump is turned on, and turns o after 1 minute. During this
cycle the heater is turned o but will be reactivated later.
XThe pumps are turned on at preset intervals, depending on
the temperature:
- temperature between 12 and 14 ° C:
Every 2 hours
- temperature between 9 and 12 ° C:
every hour
- temperature between 6 and 9 ° C:
every 30 minutes
- temperatures at or below 6 ° C:
every 15 minutes
NOTES
- If it is necessary to activate the smart winter protection during a
ltering cycle, it will be temporarily stopped and will resume where
the aforementioned ends.
- If it is necessary to activate the smart winter protection during
the “Silence” function (see “Utility functions”), it will be temporarily
stopped to enable the pump to circulate the water.
- If it is necessary to perform a smart winter cycle while a function
activated by the user is in progress, the cycle will be activated 15
minutes after the end of the function.
- If this protection is active, the spotlight may still be turned on.
QWater ltering
The water needs to be ltered to keep it clean, clear and invit-
ing. The pump runs the water through a cartridge lter in the skim-
mer (see the chapter on “Maintenance of cartridge lter”). This op-
eration takes place based on a cycle during the day (ltering cycle)
which repeats every 24 hours.
General Information
The ltration cycle has two phases:
Start
The pump is activated for 1 minute.
Continuation
The lter system is activated for the remainder of the cycle.
Setting the ltering cycles
To set the ltering cycle:
XPress the
key and hold it down for about 5 seconds. The
display will show the message dx, where “x” indicates the dura-
tion in hours.
XPress keys
or to enter the desired duration (from a
minimum of 4 to a maximum of 12 hours).
NOTE: press the “Up” key to increase the value or the “Down” key
to decrease it.
XPress the
key once again to conrm the selected value
and to continue the programming of the start delay, compared
to time “0”, of the cycle (parameter sy, where “y” indicates the
number of hours).
ATTENTION: the “0” time is the instant in which the spa is powered
or the instance where the ltering setting parameters are saved; if,
for example, the cycle start delay is set to “4”, this means that ltra-
tion will start 4 hours after the parameters have been saved or 4
hours after having turned the spa o and then on again.
XSet the start delay time (from a minimum of 0 to a maximum of
23) using keys
or and conrm with the key used to save the
values entered and then exit programming.
When this function is active, the LED of the respective symbol
will turn on. If the LED is blinking, it means that the cycle has been
suspended, see the relative chapter for more information.