Jacuzzi city spa - Underwater Spotlight; Utility Functions; Control Panel Lock; Silence Function

28
QUnderwater spotlight (multicoloured light)
XPress the key
to activate the spotlight located on the wall
of the tub (the LED comes on).
XThe spotlight will stay on for three hours, but it can be turned
o before that by pressing the key again. Refer to the user’s man-
ual for the operation of the various sequences of colours.
Utility functions
QControl panel lock
This function makes it impossible to use the panel to modify the
water temperature and ltering cycle programming; it is however
possible to activate the pump and spotlight.
XTo activate this function, press keys
and at the same
time for approximately 5 seconds (the message “LO” will ash on
the display).
XIf you press a key whose use is not permitted, the display will
briey present the message “LO”.
XTo disable the control panel lock, press key
and whilst the
message "LO" is ashing, keep key
pressed down for approxi-
mately 5 seconds.
NOTE: if there is a power outage, the control panel lock remains active.
Q“Silence” Function
City Spa™ it is equipped with a function (named “Silence”) which ena-
bles the suspension of circulation pump activity to avoid noise during
unsocial hours. A timer or timer switch (see pre-installation instruc-
tions) must be employed to use this function; its normally open con-
tact must be connected to the spa electrical box (see wiring diagram).
XUsing the timer, programme the periods during which the
circulation pump must not be activated (refer to the documents
referring to the timer).
XIt is however possible to activate the hydromassage and/or
the heater, even where the “Silence” function is active.
ATTENTION: a normally open contact (not closed) must be ex-
clusively connected to the terminal board of the electrical box.
Programme the “Silence” function so that it does not inter-
fere with the ltering cycle (in any case, the total ltering and
“silence” time must not exceed 24 hours per day).
NOTES
Do not programme time periods which are too long which could
result in skipping the ltering cycle: the water must always circulate
through the lter.
The “Silence” function disables all functions in progress, with the
exception of the “smart winter” protection.
Abnormal operating conditions
- alarm signals -
Alarms are indicated on the display, with the corresponding error code.
You will continue to see the code if the alarm condition persists.
XSignals on display
- possible solution
X“LL”
the level sensor detects an inadequate water level. The message “LL”
appears on the display and the spotlight ashes.
It is not possible to activate any function.
- Restore the water level (4-5 centimetres above the highest noz-
zles).
X“HI” Excessive water temperature
DO NOT ENTER THE WATER
The water temperature has reached or exceeded 44 °C . It is not pos-
sible to activate any function.
- If present, remove cover from spa.
- If the excessive temperature increase is due to sunlight, add
cold water to the spa.
When the temperature has dropped to below 43 °C, the spa should
re-activate automatically. If it does not, disconnect the power sup-
ply and contact an authorized Jacuzzi ® service centre.
X“Fr” Water temperature is too low.
The tub water temperature has fallen below 9 °C. However, all func-
tions remain active.
- Activate the heater.
When the temperature exceeds 10 °C, the error message disappears.
X“rPF” Defective temperature probe
DO NOT ENTER THE WATER
It is not possible to activate any function.
- Check that the temperature probe is working, or replace it.
WARNINGS
Make sure that all users know how to use the spa safely.
How frequently you should check water quality depends on
how frequently the spa is used.
Ensure that the chemicals used are suitable for use in spas;
chemicals designed for swimming pools must not be used
as treatment of water in swimming pools and spas is very
dierent.
CAUTION

Only the load-bearing covers are designed to support
weights (max. 200kg), but they must not be subjected to
violent, sudden stresses (jumping, etc.).
Do not sit, walk, or lie on other types of covers (non-load
bearing). Do not deposit objects.